Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello Nordic team,
I have a nrf9160 powered from a 3.8v bench supply.
I also have a usb to uart cable , with uart wires going into NRF9160. Usb side, plugged into my computer...
Hi
1、 The following table does not indicate whether the QDID belongs to 5.1 or 5.2.Are the QDIDs of softdevice classified as Bluetooth 5.1 or 5.2?
2、The following qdid...
Hi all!
I flashed and got both SoftDevice s130 and the example code onto my nRF51802 without prior modifications.
I flashed softdevice according to: https://infocenter...
Dear Nordic Team,
Hope you all are doing fine.
I have the NRF52-DK based on the NRF52832 BLE IC from Nordic. I wanted to implement a basic BLE Beacon that broadcasts continuously...
Hello,
I am starting to work on a sample project, wherein I need to replace the existing "main.c" file I have with "main.cpp", by copying the contents of "main.c" into...
Hi zone,
I've just got nrf9160dk and test gnss feature. Issue is: 1. Device get long time to fix. Even which many SVs in tracking and using
2. After got fix, device...
Hello there,
Recently I tried to configure the MCUBoot on my custom Adafruit feather nrf52840, based on the Windows.
Firstly, I followed the instruction below to configure...
Hi
I use PCA10040DK,My connection description：
DK's External supply + to the PPK2 logic port VCC pin DK's External supply - to the PPK2 logic port GND pin DK's External...
Hi,
Memory layout for secure dfu bootloader + main application + softdevice 332 (SDK17.1.0)
We are currently migrating from SDK 14.2.0 to SDK 17.1.0 it also affects to...
sorry I would like to install nordic on windows 10. Using windows power shell but it fails.
in pip 3 install west.
There is a newer guide that I have to follow ?
Best...
Hello,
I consider the radio collision of advertising packet, in the case there are several 10 BLE devices and the devices are powered on at same time. How does implement...
Hi,
Thanks for the great work in making VS Code a solid option for the nRF Connect SDK. It was a huge and pleasant surprise when I came across this effort. VS Code will...
Relevant configuration and device tree snippets:
Even if pm-ext-flash is defined as a SPI NOR, looks like the partition manager ignores the definition and uses on QSPI...
Hi
1 Can nrf9160 automatic select PLMN in both NBIot and Ltem mode? Is the auto select PLME default? And how to enable this auto select PLMN mode?
2 Can nrf9160 automatic...
