I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello everyone,
I was looking at SPAKE2+ example (NCS v2.6.99) and trying to understand where the password used to derived the shared secret is set or used. Can anyone help...
Hello,
I'm trying to move my project based on the xiao_ble board from using SDK 2.6.2 with Adafruit_bootloader to SDK 2.9.0 with MCUBoot/sysbuild.
To keep things simple...
nRF5_SDK_17.1.0
PCA10059
For I want to provide up to 20 central connections, I have defined the objects like this( inherited from example code):
The conn_handle is...
I have built my own firmware for my nrf54l15 custom board and got a merged.hex file.
Now I want to flash this firmware(merged.hex) to my nrf54l15 custom board on another...
Hi,
I have updated and old old project to SDK 17.0.1 and using Segger Embedded Studio
But because I make a lot of use of pstorage in the project - I am not ready to convert...
Our product is experiencing an issue where a watchdog reset occurs after DFU, even though we are feeding the watchdog in the application.
However, this issue does not occur...
Hi, I am trying to experiment the PaWR using the sample projects in NCS.
I flashed periodic_adv_rsp example in nRF52840DK and periodic_sync_rsp in nrf52832 DK. I can see...
hi,
i am trying to connect peripherials ( blood pressure, pulseox meter) with nrf5340 using uuid and mac, initially using uuid filter are used to scan the devices around...
Hello Team,
Our concerns are related to L4 security in BLE
1. We're using nRF54L15 chipset having nCS SDK 2.9, peripheral LBS example mentioned in this exercise (...
I have trained a ML model and then exported edge impulse c++ library and now I need to integrate this to project and convert the existing c base in to c++.
I have the following...
hi,
i am trying to connect peripherals ( blood pressure, pulse ox meter) with nrf5340 as a central using uuid and mac, everything works as expected. however the peripherils...
I have a pair of SDKs and have them working bi-directionally in both walkie-talkie mode (microphone) and line-in (I2S). The volume control on both headset and gateway only...
Hello there,
Working on the 54L15 and curious about the relationship between the memory map and partition example.
From multiple examples, the partition ends at 0x165000...
Hi I have a mbed application, which runs on a PSOC6 MCU, i am going to be using a fanstel BC832 (which is based of NRF52832)BT module for RF-communication. To verify that...
Hi
I use Epson FA-128 (Q22FA12800025) based on Nordic’s recommendation, but I’m struggling to compare alternatives because the datasheet lists two aging rates:
±1 ppm...
