[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We are producing an issue where the ZBOSS stack will emit a ZBOSS Fatal Error without any context if we alter ZB_DEV_REJOIN_TIMEOUT_MS. Specifically, the steps to reproduce...
Hello! I am trying to get gazell to work on the nrf52840 dongle.
I built the nrf connect sdk Blinky project with the nrf52840 dongle set as the config. then pushed the merged...
In the past, we've been able to use the nRF52-DK to flash our boards, supplying power through the debug port by shorting SB32.
For our L15 prototypes, the nRF52-DK doesn...
Hello Team,
I am experiencing an issue with the sound output from an external codec connected to the nRF5340 DK. Currently, the sound is in mono, but my goal is to achieve...
Hello,
I recently purchased a few NRF9161-DK boards for both LTE and NR+ evaluation. However, I am unable to run through the initial demo. The board is discoverable initially...
NCS 2.7, nrf52840, sysbuild with mcuboot, multiple board revisions
I have setup my build to use different keys for each board revision with this in my sysbuild.conf:
...
Hello DevZone,
I just located a mysterious bug , it's about printk() and low power.
Environment:
NCS v2.8.0 and v2.9.0
nRF52840DK v3.0.2
PC: Ubuntu 22.04
Zephyr...
Hello. I am attempting to run the Matter Template app sample on the Adafruit Feather nRF52840 Express board.
I created a pm_static.yml file with the following configuration...
Hi,
I am using nrf52840 with nrfSDK-16.0, Ble5 coded PHY( S=8 ). I am using ESP32S3 as central and nrf52840 as peripheral device. I want to connect to 8 peripherals with...
When I try to program the Thingy:91 in cellular mode, it always gives the message 'Failed to connect to port.' I’ve tried different ports, but I get the same result.
When using the nrf Connect Extension for VS Code, the nRF Connect SDK v2.9.0 and the "at_client Sample" application, flashing the nRF9160 and an actinius icarus board using...
Hello,
I'm working with the Sensor Server example from the nRF5 SDK for Mesh. I've successfully implemented the sensor model with the default publication mechanism that...
Hello,
How to use the nordic android ble library, I have implemented it but only once when on the road can receive data. From the BLE device every minute sends data.
I...
Heyy I working on project where i am planing using XIAO nrf52840 chip am using Ardunio IDE for Rapid development, I was unable to implement wake and sleep functionalities...
