I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello,
I am trying to optimize performance of a series of SPIM transactions using the 5340. Each transaction is 3 bytes long: CSN goes low, clock out 3 bytes, CSN goes high...
Hi,
I'm trying to test DFU with the Matter Light Bulb Sample, VS Code latest SDK 3.1.0, the sample is working fine with the 52840DK and is working in Home Assistant.
I...
i have given shell command through RTT and its working fine but when i try to start distribution, i am getting below error
Please advise me how can i fix this error.
Hi,
We are using Bitbucket as our CI system, and our project is based on the nRF5340. I can compile the project locally in VS Code without any issues.
Previously, we were...
I am trying to build the code for AOA example for nrf52833dk_nrf52833 dk from the example code avaliable on the sample called direction_finding_central. i have nrf connect...
Hi,
This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
Hi!
After some work with the otherwise exceptional Power Profiler software I find the current screen layout annoying:
The current display is in sync with the digital...
Hi,
I like to measure the VDD in nRF54L15DK using ADC.
I have flash the example firmware ..\v3.1.0\zephyr\samples\drivers\adc\adc_dt in my DK.
I can see it is measuring...
Hi, Good day!
I’m currently working on the nRF52832. The requirement is to support BLE + LoRaWAN (SX1276) .
I have a few questions:
How can I set up the LoRaWAN...
Hello, I have a question about the power consumption stabilisation of the nPM2100. We configured the nPM2100 with the pins directly to obtain a V_OUT of 3V with a 2477 battery...
Hi,
We are currently considering the performing DFU with UART with another MCU. Is there a sample for this application where nRF54L SoC is being updated by another embedded...
Hi,
We are evaluating NRF5340+NRF7002 setup for our customer. We are currently using https client example(sdk v3.0.2) and we would like to benchmark current consumption...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
Hi everyone, I am attempting to measure I2S rate against internal clock frequency since I am using APLL. I am following examples in NRF5340_Audio application. What i have...
