I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi
I'm migrating applications I wrote using SDK 17 to nrfConnect 3.0 with Zephyr.
I implemented USB devices with combined multiple USB classes. One of those classes was...
Hello-
I'm working on our design for the nrf9160 and I've been trying to wrap my head around the FCC certification. I know that the nrf9160 is an FCC certified module and...
I am developing a project in which a weight analog data is converted as digital by Aviva HX711.
In the host board NRF52840DK, I want to read the wight value.
I have attached...
Hello, I am new to BLE and nrf zephyr programming. I am trying to flash periodic_adv and periodic_sync samples ( https://github.com/nrfconnect/sdk-zephyr/tree/16bcaed54230e3d86aeaf2b2f1d47393967254fd...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
As the poster above mentioned, the nRF54L15 ENGA version is stuck when initializing the GRTC.
it gets stuck at nrfy_grtc_sys_counter_start().
The SDK is 3.0.2.
Is there...
We are developing a BLE application with nRF52833 512kB ROM size and using NCS v3.0.2. However it seems the ROM size occupied is not so logical, or the ROM size for NCS (Zephyr...
I am using the nRF54L15 on a custom board where I have good control and knowledge about what is going on regarding current consumption. I am using an MX25R64 external flash...
Hi
In my ble repeater application on nRF52833, when I adding OTA function , I found the my image rom size too large to adding FOTA with MCUBoot. there is my memory report...
Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...
Hi All,
I'm currently working with a custom board using the NPM1300 and STM32L4, alongside the npmx drivers. I'm trying to capture both pressed and released events from...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
