We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I baught new DK. Form last few days, I was testing sample programs for learning purpose. Suddenly, SDK stopped being detcected via USB port ? I could not diagnose the reason...
Hi
I want to increase the number of leds in DTS file of peripheral-uart sample by using overlay file.
Is it possible to manipulate the aliases in DTS file by editing the...
I'm running in to the issue mentioned in the tile; " Only spi nodes accepted in /soc/spi@40023000/". I'm using nRF connect and built a driver for the TI ADS1291 analog front...
Hi, I read a couple of post that asked about the accuracy / tolerance of the internal REF, and the answers mention it's included in the gain error.
This made me wondering...
Hi,
as stated in the title, we have a nrf52840 dongle (PCA10059) which does not come up normally on a Nvidia xavier devboard. Output of dmesg:
We tried different OS...
Hi,
I'm working on an LwM2M client that reads three sensors in sequence every N minutes and notifies the server about the value change.
The server supports the LwM2M 1...
Hello,
I am trying to use a PPK II on Chromebook Linux. The nRF Connect for Desktop software installs and runs but does not recognize the PPK II hardware. I have allowed...
Hi, I'm trying to write an app to capture images from a camera and was wondering how to monitor changes on specifc defined pins in the board overlay file. For example if(...
The certification lab is testing nRF52840 RF .They need to test LE coded S=8,Payload Type：11111111：payload length：37
but i can't find Payload Type：11111111 in software nRF_DTM...
I am a beginner I want to advertise for some time then go to sleep mode and wake up do some tasks like advertising and go to sleep mode again. Do all this process recursively...
It looks like the nRF52840 only supports:
8 data bits
1/2 stop bits
even/no parity
So 7E1 is not a supportable mode...is this true? is there a possible work around...
Hi,
I am using nrf52840 and power it by voltage 3v using CR123A battery. As per datasheet minimum operating voltage is 1.7V. But i am facing controller reset at 2.5V. What...
How do we enable a PPI TASK for a GPIO output pin configured using zephyr GPIO driver API? ex: gpio_pin_configure_dt (&ex _pin , GPIO_OUTPUT );
If I just call nrfx_gpiote_out_task_enable...
Hi,
I'm having some trouble getting a device pointer for the OV7670 Camera. I've ported the OV7725 driver. It appears as if the program exits the driver before setting...
