I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello,
I am using nRf21540 and nRF5340 in GPIO+SPI config, where SPI is controlled via MPSL and separate spi0 bus.
I have configured the board files based on nordic,nrf21540...
devicetree overlay file
// * Connecting ADC channels
// For more help, browse the DeviceTree documentation at docs.zephyrproject.org/.../index.html
// You can also...
I just ported your AWS IoT for MQTT from this repository .
If I keep IPv6 enabled, I can get the address information without any problem. However, if I disable IPv6, the...
I have a project that runs fine when CONFIG_BOOTLOADER_MCUBOOT is disabled, but when I enable it pins 15 and 16 are pulled high. I need the mcu bootloader to run but is there...
Hi All ,
Setup Used
nRF Connect SDK v2.7
VsCode
Ubuntu 20.04
Google Nest Hub2
Android 12 Smartphone + Google Home App
nRF 5340 DK
Endpoint-0 ---------...
Hello Developers,
I am k.hemasundar and i am working on the nRF52833 QAAA0 micro controller with segger embedded studio IDE. I have used nRF SDK of version 17.1.0 and 16...
Hi,
I have to develop a BLE peripheral, that communicates larger amounts of data over L2CAP. Establishing the channel between central and peripheral works. I'm able to receive...
Hello,
For the evolution of a device that uses a nRF52832 and 2 SPI's instances we are evaluating the option of adding 2 new UART's instances for managing 2 serial peripherals...
Hi there,
So, this is in a sequence of attempts to read data from a digital microphone SPH0645 using i2s master protcool on nRF5340. The program layout is as follows:
...
Hi there,
I am trying to interface SPH0465 microphone with nRF Dev Kit 52832 with the following configurations of I2S:
I have followed the code from echo example...
Hi,
I am using nrf5340 audio dk's BIS mode, connecting gateway device to a PC via USB, it takes audio data from the PC and broadcasts it, I managed to hear the sound on...
We can add the matter switch sample device to chip tool, and can be bind or controled by the chip tool, but we can not use the Apple or google APP to bind the key, It looks...
I was somehow able to work with the previous toolchain version (v2.7.0) but my application development needed an update to v2.8.0. I had previously been facing issues in installing...
nrf Connect Terminal overwrites LD_LIBRARY_PATH. I have added SEGGER JLink path to it so nrfjprog and JLink can dynamically link to the JLink dot so files. This works on Bash...
I am running nrf5340_audio_applications on the nRF5340 Audio DK. Follow the requirements, i add an external flash shield. I've only changed
the configuration of flash and...
