I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
I am trying to run the sample using NCS v2.5.0. This is what happens on the console when I try to connect from the dongle, when running the Test Procedure:
The discovery...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hello,
I recently migrated to SDK version 3.2.0-preview, which supports Matter 1.4.x.
When I use ZAP and add a new endpoint to the light_bulb example under the name Electrical...
Hi I'm trying to communicate with ICM45686 using nRF54H20 and SPI CLK, MISO, MOSI state appear correct but CS pin is not asserting/deasserting following it the scope capture...
Regarding the nRF54L15-DK development board and its use with BlueZ on an Ubuntu virtual machine: After flashing the hci_uart example onto the nRF54L15-DK board, I used the...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
Hello, I am facing an issue in nrf52dk (nrf52832dk). Whenever I access i2c0 bus for the controller it works fine but whenever i switched on the i2c1, it starts giving me device...
Hi, I`m working on a custom board. I have been playing around with it for a couple of months, but just recently stumble upon a strange behavior. This is a custom device where...
Hi, I am trying to use the external flash on the nRF54L15 DK with QSPI to perform the zephyr/samples/subsys/fs/fs_sample sample.
I am using NCS v3.1.0 (on Windows if that...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
I currently evaluated the use of the "<modem/at_parser.h>" (at_parser module).
Using it with the at-cmd "at+CEINFO?" is very irritating.
I 07.324 : CEINFO: +CEINFO: 0...
Our team is transitioning to the nRF Connect SDK after extensive experience with older nRF SDKs and custom build systems (based on cmake + west + python) integrated with VS...
I would like to know if in mesh device for the comuniation are used all that channel or only the 3 channel that are used for the advertising channel or all the channel 37...
Hi
any one a clue why I see this bar twice?(see attached picture)
Some thing probably went wrong with my previous older installation.
I already reinstaled Wireshark...
