Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I am using android nrf mesh app as a base app and using the latest nrf mesh library version.
I am taking provisioning trails on inline on-off controller.
While...
Hi,
I have used "write_handler(p_ble_evt->evt.gap_evt.conn_handle, p_rtc_service, p_evt_write->data[0]);" to send data to nrf52832 from nrfconnect mobile app but iam able...
Hello,
For our application, we need to form a Zigbee distributed network and not a Zigbee centralized network. That means that routers need to be able to form a new network...
Hi , I have a problem when I wanted to combine the two examples twi scanner and usbd ble uart together although they work correctly individually I have a MAX30105 sensor which...
Hi all
We're developing an application for nrf9160 with zephyr-sdk v2.4.99-ncs2 and nrf-sdk v1.5.1.
In our project we are required to use a Library which forces us to...
Hello
I want to sampling two analog.. with different configuration and handler.
so I set two channels like this.
and then I call only one sample function like...
I'm working on developing a device using the nrf52832. Currently using the nrf52 PCA10040 dev kit. I'm extending the zephyr/samples/basic/peripheral_dis sample in order to...
When compiling the net CPU with debugging configs such as CONFIG_DEBUG or CONFIG_DEBUG_OPTIMIZATIONS enabled and the resulting hex is flashed to the nRF5340; If then an Ozone...
Hi I am wanting to use the ARDUINO 4 RELAYS SHIELD with the nrf52480 or at least see if its possible.
https://store.arduino.cc/arduino-4-relays-shield
relay data sheet...
I wanna use nRF52820 to make some application development.I wanna a sing-board development kit for nRF52820 ,and nRF52833DK supports development on the nRF52820 SoC and nRF52833...
Hi Everyone This is my first time designing a PCB with the NRF51822. I have designed it using an 2450AT18B100E Antenna and a BAL-NRF02D3 balun. Below is my schematic:
...
There are discussions on WLCSP light sensitivity for nRF5 product, which affects RF, clock accuracy, and low power current draw etc. what about the nPM1100 which clock accuracy...
Is my understanding correct that with VDD supplied and ENABLE = high, having VDD_GPIO floating (i.e. disconnected from a regulated 3.3 V supply) is a valid state? We intend...
hello Nordic
i am working with nrf52840 sdk16.0 s140
i wish to read the UICR register value like this :
but i get this compilation error
since it is a define...
Hello, I'm working the nrfx saadc legacy driver, and despite changing whether I measure Vdd(on the dk) or GND, the saadc output(p_event->data.done.p_buffer[0]) oscillates...
