Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hey All
Im working on a new product and its the first time I'm developing around the nrf5340, I'm looking for some guidance around the supply configuration for maximum...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
I am getteing a -12 error when trying to access a open/create a file using littlefs and a fs_open command on a nrf5340 custom board.
The filesystem seems to be mounted fine...
Hi,
Platform: nRF54L15
SDK: V2.9.0
The application is Matter + BLE.
We would like to use X509 certificates which will be used for authentication when the application...
In 2.7.0 in file c_cpp_properties.json I had direct path to compiler. Now moving I need to change the path.
AI suggested to use ${nrf-connect.toolchain} for compiler and...
I want to use the UART to receive data, but that doesn't look possible if I use the Logging Module. I don't see where the logger module will interrupt my code to tell me I...
I'm currently working on a project using the nRF52832 as my controller, Segger Embedded Studio version 5.42a as my IDE, and the nRF5 SDK 17.0.2. I started by developing a...
Hello,
We are using the Message Routing API of nrfCloud to consume messages via Webhook and DLQ. We have several devices placed in different device groups (e.g. prod_devices...
Somewhat related to this:
I'm wishing to optimise code (removing a load of volatiles) by ensuring most of my application code runs at the same interrupt as the NRF_SDH_BLE_OBSERVER...
Hi,
I have 2 problems in power profiler kit II:
Problem 1: When I connect the porfiler kit II to the computer, the computer can't identify the PPK2
Porblem 2: The output...
I want to know how to adjust the TX RX setting for the nRF52833 DK connected to the nRF21540 EK shield. I have already added -DSHIELD="nrf21540ek" to the build configuration...
Hello.
I am trying to repeat the functionality of the project that is shown in this video https://www.youtube.com/watch?v=fCU8x-pmtqU&list=PLx_tBuQ_KSqG-leiJDfOKf_ZmCqHnbi4r&index...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
Internet connectivity is provided to the WT02C40C module via a hotspot, with CONFIG_STA_KEY_MGMT_WPA2...
The "nRF Command Line Tools" page, https://www.nordicsemi.com/Products/Development-tools/nrf-command-line-tools says " Important: The nRF Command Line Tools is in the process...
I want to interface 3 custom made heater boards to nrf5340dk. Where the simple task is to toggle gpio's to Turn ON & OFF the heater board. Now, we are using P 0.01, 0.02 &...
Hello, I am considering the prospect of using channel sounding as opposed to UWB for indoor asset tracking. I can understand, that the main limitation with that would be,...
Hi There:
I used the nRF7002 DK to evaluate its WiFi throughput performance.
The test environment is below:
1. nRF7002 DK
2. NCS version: 2.5.0
3. Sample application...
