Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hi,
I'm try to set up a UDP server on a nRF9151dk, and send data from a remote pc to the devkit. I have tested my sim and networking works correctly, I am able to use coap_client...
Hi,
I am using the nPM1100 in my new application, where the system power circuit includes two additional 250mA LDOs configured to provide a 3.3V output . I am also using...
Hi,
I am encountering the following build error with the BLE peripheral example after migrating from NCS 2.7.0 to 2.9.0 and when CONFIG_BT_LL_SW_SPLIT=y is set in prj.conf...
Hi,
I am using nrf Connected SDK v2.6.2 on windows 10. I try to create a blank application project for the device ADXL363 on SPI2 bus on the nRF9160DK board.
I basically...
hi:
I use ncs 2.8.0 ,nrf9151 dk and v2.8.0\nrf\samples\net\https_client.
I modified the DigiCertGlobalG2.pem
this is log:
connect() failed, err: 111.
What is the...
Hello,
I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
We have designed a vehicle tracker that uses the NRF9160. We have found in the past that sometimes after the radio has been running for a while it gets into a loop where it...
Hi,
I try to develop a Bluetooth speaker using the nRF 5340 DK since i do not have a separate audio Dk for this. I am using the sample code Audio unicast client for this...
Hi
I have a project developed on the nrf52840dk / nrf52840 dongle and am trying to build it for the Laird BL654 dongle. The build fails due to a missing 'runners.yaml' file...
Hi all,
I'm looking into speeding up my workflow using remote development containers on ARM servers, but it seems some tools are missing, nrfutil the first, to run a fully...
When I get a custom board, how do I detect and flash it? I have three options on the board:
I have a USB cable with:
GND
D+
D-
+5V
OR can configure the usb...
Hello, I'm trying to get nrf5340_audio example running on nrf5340 audio dk.
I'm able to build the code and run it however i'm unable to bond with my mobile phone with android...
Hi,
I'm using ncs 2.9.0.
I configured the GPIO in device tree like this:
And I used it in .c as follow:
But FATAL ERROR was got when the gpio_pin_interrupt_configure_dt...
Hi! In order to get more accurate battery SOC measurements I need to provide a custom battery model to the app. So, I had to use the nPM1300 EK + Fuel Gauge board to profile...
Our device is set up to provide AT Commands directly to nRF9160 using a USB UART connection and control using a VT100 Terminal simulator. When attempting to connect to the...
