Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Good day
Our custom board contains RS485 implementation. The file schematic for that looks like this:
I have noticed that a driver and sample exists but the driver doesn...
Hello everyone, I'm currently updating my project from SDK v10 with softdevice S110 to SDK v17.1 with softdevice S132 (a huge step). I'm, wondering if what I want my code...
Hi
I am trying to make a SPI connection with a device which doesn't already have a driver build into Zephyr.
Is there some kind of genereic device i can use since i just...
Hello,
I am trying to send data from a delta-sigma 32 bit ADC - the front-end is an EEG amplifier - via WI-FI to my broker. I would like a recommendation related to the...
Hi,I am using NRF5340 AUDIO DK BOARD and I have been trying to access i2s mic and I want to transfer the mic data to Amplifier .Is it possible to do with single I2s ? As I...
Hello everyone,
I'm experiencing some issues while trying to program an nRF52832 CIIA on a custom PCB. Specifically, I cannot get the GPIO pins or the external 32kHz crystal...
Hi, I checked DFU over Wi-Fi in a separate project (net/download) that only included DFU and Wi-Fi-related functionality. In which FOTA is working as expected.
In our custom...
I have just started programming the using the nrf52840DK_nrf52840. I downloaded the toolchain and sdk using the VS code extension and created a new application from the blinky...
Hello,
I just upgraded from v2.5.0 to v2.7.0 of the SDK. To do this, I had to modify my files of my specific board and use sysbuild.
My project compiles and works on my...
Hi All,
I'm considering using the nRF5340 in an audio application. I'd probably go for a 3rd party module in order to avoid getting FCC certs on my own. Possibly the Fanstel...
In Section 6.17.1, page 543, of the nRF52840 product specification version 1.10, in regard to the Pulse-Width Modulation (PWM) peripheral, there is a statement that says ...
Good morning,
I am try to build a application from example list, Bosh bme680 with supported board rak4631_nrf52840, and I am receiving a error message, but if I try to...
hi ,
I am currently developing a project using the nRF52810 as my controller and SEGGER Embedded Studio (version 5.42a) as my IDE. I have successfully integrated the Timer...
Hello
I want to make an application based on the multi NUS sample https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/enter-the-multi-nus-a-simple...
Hello,
I am practicing the intermediate Nordic Academy online course, and I have a problem of the thread viewer.
I have enabled debug, I did everything strictly according...
