We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
Can anyone point me to a good example for Polling mode using serial library?
I'm looking for an application in which I can poll the serial port for data. I went...
I'm investigating the flash usage by the peer manager to store bond related data. While I haven't had a chance to fully investigate how the FDS and fstorage modules work,...
Hi,
We have a need to have a Nordic app for nRF51822 which both serves as a beacon and also offers a connectable service.
It's my distinct impression at present we cannot...
Hi,
My setup :
nRF52832
Soft Device S132 v5
SDK14.2
My use case involve me to send data to to a central device at 50 meters. I need to send only a small data...
Hello everyone :) , I work on a project initialy configured for a PCA10040 board and I would like to use the debug with my PCA10056 board but unfortunatly the debug doesn...
Hi
For some reason I get stuck in softdevice at 1EA7A when a send some random data to my phone also I notes that function sd_ble_gatts_hvx return 3401
PC = 0001EA7A, CycleCnt...
I am trying to connect thingy as peripheral and many smartphones as central but i can connect only one smartphone by using thingy at a time.Is it possible to connect many...
[References]
In page 234 of nRF52832_PS_v1.4 it says "In both modes, the TIMER is started by triggering the START task, and stopped by triggering the STOP task."
In this...
I am trying to add a custom service to support a communication path in my project. The Nordic UART example gives a good place to start so, using that as a template, I have...
Hi All:
i met a trouble.
i want to implement a function that i can restore mesh device by uart cmd.
so , i add uart to light switch service demo, when i recive a cmd...
Hi,
I tried the BLE Uart example on my own nRF51 board, but after a few minutes the application hangs in the softdevice.
The board is one we developed, an FTDI cable...
Is there a way to retrieve 128-bit base UUIDs from the SoftDevice, either the "built-in" Bluetooth SIG standard or a vendor-specific one registered via "sd_ble_uuid_vs_add...
Hi,
I'm having problems running the ble_peripheral/ble_app_blinky example with my iPhone 7 and nRFConnect. Here are the specs for the tools I'm using:
nRF52-DK: PCA10040...
Hi all,
I am currently trying to develop my own Secure BLE DFU bootloader from the example provided in the SDK 12.3.0. I don't work on the DK, I have my own board with a...
