Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi there,
I am trying to get nRFConnect working in VSCode, but when i click on things in the welcome screen it only shows "activating extensions..." in the bottom bar. I...
1) On p. 55 of nRF52805_PS_v1.4.pdf, section "5.3.8 Reset behavior" shows that a pin reset will reset GPIO, so will a pin reset active low also reset PSELRESET registers,...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hi,
I have built and run the MQTT sample for an nRF7002-DK and had it work as expected (connect, publish messages to test.mosquitto.org).
Now I'm trying to get that sample...
I created a new application using the "Create a new application" > "Copy a sample" > "zephyr/samples/basic/blinky" option in vscode. And I added a new build configuration...
Hi Nordic community,
I'm currently working on a project where I'm aiming to implement FOTA updates on the nRF52840 DK, with the application images stored on the MX25R64...
Both a colleague and I discovered that the default Device Provider, nrfutil, is not working in the current versions of VS Code and nRF Connect for VS Code extension. nrfjprog...
Toolchain v2.6.1 installed. Attempt to Manage SDKs fails.
[13:12:52] nRF Command Line Tools 10.24.2 are up to date Command failed: git ls-remote --tags --heads github.com...
First attempt to use the Power Profiler II on Windows 10 didn't work. I was getting [sdfu] No deviceInfo available for the device, code: Argument. Message: Operation device...
I would like to perform a test to confirm the receiving characteristics of the nRF52840. When I looked at the RF Performance Test Guidelines White Paper, I believe it said...
Hi,
We were testing MCUboot uisng nRF52 Dev Kit and ran into an issue that updated firmware in slot1 couldn't be booted:
Since we don't need bootloader upgradability,...
Hi,
I upgraded my nRF5340 Audio application from NCS v2.5.0 to NCS v2.7.0 to be able updating the network core.
I noticed that in NCS v2.7.0, the nRF5340 Audio application...
Hi,
I am currently developing a project using the nRF52810 as my controller, with SEGGER Embedded Studio (version 5.42a) and SDK version 17.0.2 as my development environment...
