Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Dear Dev Team,
I am currently working on implementing OTA DFU on the nRF52832-DK using the Arduino framework. However, I have not been able to find any suitable options...
Hello!
I am currently using INA219 (Zephyr I2C driver included) current monitor to test I2C function on nrf54l15dk, but the board cannot recognise the sensor successfully...
I am trying to build using a custom board and 2.9.1, but am getting these errors:
My dts looks like this:
I have the width specified. Much of this is over...
I am currently looking into the Legacy DFU process. Currently the only way to actually conduct a Legacy DFU is via the nRF Connect Mobile App. After conducting a successful...
Currently using NCS v2.9.1 nrf54l15/cpuapp custom board derived from nrf54l15dk, customization to de added after solving the issue below.
The project is successfully compiled...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Hi,
I'm using the Ellisys tool to capture packets and compare the differences between CIS and BIS. The capture results for BIS show that it is unencrypted, as seen in Figure...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
We have developed a hardware platform using the NRF5340 on Nordic's zephyr (version 3.5).
Our current consumption in idle mode is still around 330 µA, instead of the expected...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Hi, I'm working on the DK for nrf52832. I have a working code for BLE, and another working code for die temperature using interrupt. Now I want to merge them and trigger the...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
We have an nRF52840 device that is required to do continuous BLE scanning in central role to find nearby advertising beacons and is never required to establish a connection...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Hello,
A quick question about using an nrf9160 (+ sdk 2.5 - modem 1.3.5)
When I activate the following parameters: # LTE-M (LTE-CatM1) CONFIG_LTE_LINK_CONTROL=y CONFIG_LTE_NETWORK_MODE_LTE_M_GPS...
