I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
Hello, We are working on a project based on the Thingy91x which uses the following SAW filter : SAFFB2G45MA0F0A. Unfortunately this part seems to be out of stock everywhere...
Hi
I am maintaining a NRF project, done all Dev Academy courses 2 years ago, still I am havibng trouble.
My current task: I need to set a (hardware) timer interrupt with...
Hi Support
We are in the process of integrating the NPM1304 into a small battery (55mAh) wearable device. I am finding it hard to figure out section 7.3.2
regarding the...
Hello,
I am not able to send any data through the pins of port P2 using Pins : P2.0, P2.2, P2.3, P2.4 , while the pins P1.11, P1,10, and P1.4, P1.5 are working properly...
I am trying to capture steps and wrist wakeup ( https://github.com/zephyrproject-rtos/zephyr/blob/4c6b1e5a65e752c881183ddb4687fa0231b11cc3/drivers/sensor/bosch/bmi270/bmi270...
Hello I am doing research for my paper which includes using MCPD distance measuring between nrf52840dk boards. I currently use nrf_dm sample to measure the distances. I have...
Hello
I'm using NCS 3.1.0 and I’m able to use signed files for FOTA. However, I would now like to add encryption, but I can’t figure out what’s not working :
app/ ├──...
We are preparing a product for production and have enabled authenticated debug access on the NRF52840. Because authenticated debug access is not described in any Nordic documentation...
Hi, I've installed Visual Studio 1.90.2 + nRF Connect for VS Code Extension Pack v2023.11.3 + v2.6.1 toolchains + v2.7.0-rc2 SDK. Then I create a new application, copy a sample...
Hi,
I'm having a problem with sending notify packets, I'll describe the situation I'm doing.
Problem :
I have 5 devices connected to the board and I want to send a first...
Currently on NCS 2.9.2 and radio_test is buildable with CONFIG_BT=y and CONFIG_COUNTER=y. Trying to switch to 3.1.0 but getting an error that "MPSL reserves TIMER10 on this...
Hi There
I run a NRF52840 with the MESH SDK, and use the Flash manager provided.
After some time i would like to update the Device over FOTA this ends in a Assert on booting...
This is my basic information:
1. SDK version: V2.8.0
2. Project: Matter Light Bulb
3. Board: 52840DK
This is my question:
I can use this command to commission bulb...
Hello all. I have an issue in production of a device that utilizes the 52833, aQFN73 7x7mm package, in regards to the pad stack dimensions. I wanted to check the datasheet...
