Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have code working for interfacing the nRF52 DK board to a SSD1309 based 2.42” OLED display.
The problem is with getting the correct indexing for lines and columns.
Can...
Hello,
we are experiencing rejection from the network by receiving cereg notification. Modem afterwards stops attempting to connect to network. Which results in application...
I had used nRF52840 DK sometime ago and successfully tested it with different codes. But now when I connect the kit to the PC, it is not getting detected by the same PC that...
We just ran into an issue with multiple build names for nRF Connect's plugin for VSCode on Mac.
Start with "Launch build_a", "Launch build_a_v1", and "Launch build_a_v2...
Hi, here comes a few VSCode plugin bugs, it's really the first one that is the main one, but thought I might as well "dump" the rest of the quirks and bugs I have with it...
Hello,
I am unable to see my Nordic Thingy 53 using the nRF connect desktop app, I can use the apps on my phone, but I need to be able to use my computer for a class....
Hi Nordic Teams:
I'm using Nordic Connect SDK v3.1.0 and nRF52840, I want to update USB iSerialNumber string in hid-keyboard samples.
I tried two methods but they didn...
Hi,
I'm not able to flash nRF54 DK. Log as below:
2025-08-29T06:47:39.828Z INFO Initialising the bundled nrfutil device 2025-08-29T06:47:39.874Z DEBUG Started watching...
*Note that this is only an issue when the central and peripheral are simultaneously active.
This is my current setup for starting advertising, but it requires a deprecated...
Intro We are using the nRF9160 with sensors we manufacture. The code developed is based on the serial SLM sample, toolchain v1.6.0. I am trying to keep the code/project files...
Hello. I have an issue with my development board. When attempting to recover the board, i cannot due to access port protection. This is the specific error message from the...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
am trying to mount little fs example with my external flash winbond w25q256 but my nrf52840 board taking internal memory and am using qspi
it get automount and writing in...
Hi Nordic,
I need to build an Auracast broadcast speaker (LE Audio BIS broadcaster). Besides audio, I also need two-way data exchange between the Auracast source and the...
Hello,
I am trying to have my own BLE advertising and scanning (with filtering) custom service (from now on peer service) in parallel with BLE mesh. So far I've been able...
