Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
When using jlink to connect to my board in VSCode, it displays "unknown device"
nrfutil device recover
I tried a few of my boards, but the result was always the same...
Hi everyone,
I’m working with Zephyr 3.2.3 in a Windows environment and trying to run the shorter connection intervals sample: https://github.com/nrfconnect/sdk-nrf/tree...
Hello Nordic Team,
We are trying to test an external audio DAC (TLV320DAC3100) using the nRF9151 DK .
As a first step, we attempted to build the i2s_output sample from...
Hello Nordic Team. I'm currently facing an issue when building in release mode (CONFIG_LOG, SERIAL, CONSOLE disabled). The issue is that after a random time (no longer than...
As shown in the figure below, I measured a voltage of 5V at the location marked in red, and measured a voltage of 0V in the components within the yellow box。
Is it absolutely...
What is the switching frequency of the internal DCDC in 54L15? What is the function of the FB1 ferrite bead in the reference design? Are there any risks in changing the capacitance...
I am extending one of Qorvo's UWB platforms.. adding Softdevice BLE functions.. (which work ok) (this is on sdk 17_1_0)
the coprocessor uses a GPIO connected signaling mechanism...
Hello!
We are a student group from NTNU which is developing an BLE Audio Beacon using the nRF54L15 socket and the nPM1300 PMIC. However, we have ran into some issues when...
Hi, I am trying to optimise for raw TX throughput. I am running the raw_tx_packet sample. I am using a nrf7002-dk and running v3.1.99 with the following configuration changes...
Hello,
I am currently working with the Nordic Power Profiler Kit II (PPK2) and the Nordic Thingy:53 for current measurement experiments.
Setup
I was using PPK2 to...
Hi,
I'm trying to use the bitcounter to drop packets that don't comply to a specific UUID. I'm working with nrf52840.
My question is - if the received packet is shorter...
I’m working on a custom board based on the nRF9160 (SICA variant) and trying to enable MCUboot + TF-M with sysbuild. I’m running into an issue where the system never reaches...
If a device has established a PDN connection, is it sufficient to rely on lte_lc's pdn module to determine if a network connection has "failed" due to being out of range,...
Nordic Team:
We have a product in production that uses the nRF9160 and nRF7000 and had assumed the nRF7000 did not transmit. We only recently discovered that it does, in...
Hi
How can I use ztest to calculate code coverage on the nrf54l15 platform, I tried to use the configurations of CONFIG_FORCE_COVERAGE=y, CONFIG_COVERAGE_GCOV=y, and CONFIG_COVERAGE...
