after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Dear support
I need to pass 128 bits service uuid to discovery process as variable, I have an array of 16 bytes of uuid number, it is divided into five parts as show here...
I am trying to use the PPK2 for measuring current consumption on a device powered by 24VDC by connecting PPK2 on the low side of the DUT towards the power supply - but fail...
Hello, I'm working on an application that needs both ANT+ and BLE (s332) and the ANT+ part is done. I'm having a hard time understanding how to read analog data, like a battery...
Hello,
we tried to create a Matter build with the Nordic SDK.
Following Steps are done by us which are causing the error:
Clicked nrF connect extension in VS --> Create...
Hi,
I am working om a project in which i need to send few data through NRF52832 serial port and via BLE I need to update the same to NRF connect app
I have tested the...
Dear Brother and sisters
I want to display Real time ,Date ,month on a lcd using internal rtc of nrf52840
its not working properly..
I have to reset the time again and...
Hi all,
I tried searching for related posts but could not find a clear answer. Basically we are trying to build a device that supports both BLE and Matter. We do not need...
Hello all,
while I am developing the project, I need to add certain configs to the SDK ... it is becoming an extremely complex configuration, of course I am totally new...
Hello
I need to setup TLS communication using UDP, betwen:
- zephyr app as client
- ubuntu pc, openssl server as server (ofc)
I modify prj.conf of sample disabling...
Hello all!
I coming across a strange problem, the emStudio does not want to accept the nrf_log_frontend file not matter the file is in the folder, under the sdk folders...
Hi,
I have built and tested the CLI sample project on nRF52840 DK as well as a custom module. Now I want to extract the parts used for thread commissioning from it. I tried...
Hi, I'm trying to port my NRF SDK15.3 application to NRF Connect. I made a custom board for my PCB and I can control the LEDs with PWM etc. Now I'd like to read data from...
Hi,
I have a custom pcb with NRF52840-QIAA-F-R (rev3) on it. And when I tried to program it first time, nrfjprog shown the folowing error:
ERROR: The operation attempted...
In the mesh serial example, I found that the sequence number isn't stored into persistent flash. If that is the case, if the board is power cycled, no one can communicate...
