Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I have ported my already working nRF52840 SPI slave code to a nRF5340, but it doesnt seem to receive any data. I have verified the CS, SCK and MOSI signals, but no MISO...
Hi,
I was wondering, what is the professional, assembly line ready procedure to program the IMEI on an nrf9161?
So far, I've only found rajeev's post in this discussion...
Hello,
I am using a Raytac MDBT50Q (nRF52840) on a custom board , and I am trying to blink an LED, but it is not working.
"I need urgent help as this is blocking my...
We can get BLE address in adv report: How to get mac address of nearby ble devices? - Nordic Q&A - Nordic DevZone - Nordic DevZone
At that moment, peripheral not connected...
I have download this .zip from the Nordic site. I am a beginning coder and I am using AI to help assist me on my project and learning C code. I seem to unzip the file correctly...
Hi, I am trying to understand periodic advertising and some basic questions:
I am using periodic_adv example from the NCS.
I see teo ADV data defined in the file as...
NCS 2.7
NRF52840
SPIM3 at 32 MHz.
I have CONFIG_NRF52_ANOMALY_198_WORKAROUND=y and have confirmed the workaround is being activated by setting breakpoints in my code...
Dear,
I need to generate a pulse signal on one IO following this pattern: HIGH for 12us ; LOW for 106us ; and so on...
I tried to use TIMER0 with NRF_TIMER_EVENT_COMPARE0...
Howdy,
I am using an nRF52840 to perform BLE communication. For this communication I am using extended advertising to perform most of my data transmission. Thing is though...
Hello, i have a device supporting DFU OTA i'd like to create a small tool for flashing firmware from the computer to the device. I've set thr device to DFU mode. Is it possible...
I just got a PPK2. I was able to use it perfectly with Power Profiler. Great tool! Today I wanted to learn more about nRF Connect other applications. (Actually I was looking...
Hi there, I'm having so much trouble trying to get this two nRF9161 DK to communicate using SPI, being one Master and the other one Slave. I'm using the spi3 driver for SPI...
We had three nRF52840DK boards (PCA10056) for several years for use in development. Then one died (or to be fair, I killed it), so we got two more that turned out to be newer...
While using nRF Connect, I encountered an error when attempting to enter Debug mode with RTT active. Here are my J-Link specifications and log details:
When I have...
