Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I'm able to flash ble_app_ancs to the nrf51822, and I'm able to debug it successfully. I'm also able to pair with my iPhone 5S running iOS 7.1. After the initial pairing,...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Good afternoon,
I'm trying to test PCA10001 eval board power consumption and consumption is about 4mA when it should be considerably lower.
To proceed with this measurement...
Hello !
When i was trying to configur my SPI, I observed that there is a difference between the position field announced in the nrf51 reference manual v2.1 and the nRF51_bitfields...
We are looking for the sample software for transmission of nRF2726 (nRF24Lu1P).
nRF2726 does not carry out transmitting operation in enhanced_shockburst_ptx_nrf24lu1p.uvproj...
What I've been observing here is a curious issue under some very specific circumstances. First off, I am using a Xuntong Tech PTR9018 module (this is QFAAC0), the S120 1.0...
Hello all
I making some device with ARM core CPU with nRF51822.
I set CPU to SPI master and set nRF51822 to slave.
And then I read some data from nRF51822, that was...
I am Merging 3 firmware s110_nrf51822_7.0.0_softdevice.hex, ble_app_beacon.hex and bootloader.hex to Output1.hex as follows.
mergehex -m s110_nrf51822_7.0.0_softdevice...
I'm trying to use the Bond ACI command on my nRF8001, but I'm having trouble using it as per the datasheet.
When I set the Timeout parameter to more than 30 (0x001E), the...
The documentation for the nRF51 says only code from code region 0 can execute the erase and write command on code inside code region 0. This means that my bootloader in code...
I flashed S110 softdevice and ble_app_hrs application to nRF51822 on PCA10005 with nRF6310.
and then I tested by nRF toolbox on iPhone5s.
But ble_app_hrs application seems...
I'm attempting to implement a buffer in flash using the persistent storage module but have hit a bit of a wall. When I manually set the block size to something less than the...
Hi,
i'm developing an app for Android and iOS that needs to comunicate with a devices based on nRF51422 with S110 v7 loaded.
We want to encrpyt all comunication and enstablish...
Hello All,
I would like to implement static pin on my sensor. Remember how some Bluetooth Headsets are hardcoded to '0000' I would like to implement '123456' since BLE...
