Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I observed that the asset tracker application will not run using code starting with commit a507a3e42229544b195e93a9896ca09c8a4fba85 and newer, on the master branch, in repository...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
I have a binary file for a 3rd party device that the manufacturer has asked me to test on their devices. I have looked through the ZigBee OTA example documentation but it...
Hello:
I am working on a USB bootloader where I have enabled the WDT on entry. After I enable the WDT, the app_timer is set to feed the WDT and to also signal the end of...
Hi
I have a new Thingy:91 that I'm updating.
After I updated the modem software and the firmware with Connect desktop Programmer.
When i could not connect I deleted...
We recently had an issue where a race-condition was caused because we handled entry to sleep mode a bit too carefully. Therefore, I wanted to discuss different methods to...
Hello!
USing help from this forum i have successfullz transmitted adc value from one pin of AIN# to ble and reasing values successfullz but now i am facing an issue that...
Hi Nordic Team：
I use version is: nRF52840 DK Version：nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\ncp\ftd\uart\hex
Raspberry Pi 3 Version：RaspPi_OT_Border_Router_Demo_v4...
I am new to nrf52.
I want to configure TIMER1 as a counter.
However it does not count. I have added it after advertisement_init
Does the nrf52 have any such limitations...
Hii nordic;
I need to encrypt and decrypt my advertising data i.e;UUID,Major,Minor,etc.; of my nrf52832
So it cannot be seen by third parties
my sdk version is 15...
While trying to communicate through I2C/TWI with a MCP39F521 using a NRF52 DK (NRF52832), the first bit of the received data is always 1. The NRF52 DK is the TWI Master and...
Hi, I'm newbie to nRF DKs but started trying to run examples from pc-ble-driver-py / pc_ble_driver_py / examples / on github in order to get familiar with the nRF52840. I...
Hello
I'm setting up a set of Thingy91 and Thing52 units.
1) I registered 2 thingy91 sim cards and registered the nodes. 2) I see the SIM card in my account on nrfcloud...
I'm using a nRF52480 DK board with an adafruit 3421 I2S microphone breakout board attached. I am on Ubuntu 20.04 with SES 5.42c and SDK 16.
I am using a variant of the usbd_cdc_acm...
Hi,all
I am developing a Bluetooth product with HID function.I refer to the official keyboard example.I modified the "report_map_data" to implement some special keystrokes...
