Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
My goal is to achieve a data throughput...
We are connecting nrf boards to solar charged batteries for power consumption. We will be remotely deploying the boards on field. The boards are connected to sensors, from...
I'm going from v2.6.1 to v2.7.0; I'm using a thingy53. I'm getting a voltage error prior to boot.
[00:00:00.002,929] <err> voltage: setup: -134 *** Booting nRF Connect SDK...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
Hi,
I evaluate MCUBOOT and trying to understand how it works. I am using a nRF52840DK. I have base my demo on this course ( Exercise 1 - DFU over UART - Nordic Developer...
Hi,
We would like to disable all wakeup sources before calling sys_poweroff. How to achieve this using Zephyr API? Pin configuration should remain as previously configured...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...
I am running the demo about knx iot. (branch: v0.3.0_rc in https://github.com/NordicPlayground/nrf-knx-iot )
I build and run "light_switch_sensor" and "light_switch_actuator...
basically, I want to use dm feature in connection-oriented communication. not in connection less, and I want to connect 1 central to 4 peripheral and measure distance.
Can...
nRF Conncet for Desktop v5.0.0
Hello,
I have some trouble to update the Toolchain Manager of version later than v1.2.6. The download fails. However, I can download the...
Hi,
We are working on a project using the nRF52832, which utilizes UART for a QR-code sensor, I2C for an OLED display, and SPI for external flash memory.
We are at the...
Hello.
I am trying to write protect the Flash area using nrf52840's ACL peripheral. I tried to perform the same process on the main processing side by referring to nrf_bootloader_flash_protect...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. Can I advertise a special data? like 0x08,0xff,0xa6,0x02,0x33,0x09,0x55,0x00,0x0c. 0x08 is packet...