Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
I have LIS2DW12 (Gravity board) connected to my NRF54L15-DK with the following overlay:
& pinctrl {
/* Pin control for I2C21 */
i2c21_default: i2c21_default...
Hello,
I have set up the light and light_switch BT Mesh examples on my nRF52840DKs. I have used the nRF Mesh app to provision them successfully and I can see that they work...
Hi,
I am using NRF Connect environment and would like to enable by program to use MCU Boot functionality with dual-imaging support and FOTA updates.
My Kconfig.sysbuild...
I need to change the path of ncs. after try sometimes, I failed. So, I need remove all the settings and retart my work from initial status. I uninstall vs code. and install...
Dear Nordic Team,
I am trying to configure logging through J-LINK RTT for my firmware.
My prj.conf contains the following:
CONFIG_PRINTK = y
CONFIG_CONSOLE ...
My current product uses the NRF523840 with CODED_PHY periodic adverts. I want to improve the range.
I'm considering a +14dBm (SAR limited) product variant with the NRF54L10...
The nPM2100 datasheet (v1.0) states in multiple areas that the VOUT pin is discharged when the device enters Hibernate mode (and certain other modes).
Is this discharge...
Hi
It seems that the default minium DTLS handshake timeout is about 1 second. That means, there is a retransmission if a response isn't received within this timeout. In...
Hi there,
I am trying to program my custom board hosting a raytac mdbt53 module (powered by a separate USB cable). I have to use the custom connections in P20 connector...
Description: We are working with nRF54L15 connected to an external flash memory MX25R64 . Our setup uses MCUboot with a secondary partition located on the external flash....
Description:
We are using nRF54L15 with NCS v3.0.0 , and the following clock configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL =y
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM...
The standard 802.15.4 message FCF define an Acknowledge-expected bit. It is implied in the documentation that the radio will send the Ack automatically in Assisted mode. 1...
Hi,
I am having an issue with matter device commissioning after updating from NCS v3.0.2 to v3.1.0. Prior to the update, the device was able to join a matter network running...
some days ago, my vs code can run the most jobs for nrf connect. it works well.
but now. I cannot find any valid tools (build debug ....) in nrf connect label in vs code...
The STM32 chip collects audio data with the following audio parameters: a sampling frequency of 44 kHz, a sampling precision of 16 bits, and a single channel. The STM32 chip...
