The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hello,
We are currently looking to implement an RFID tag reader in a project I am working on and I am wondering if the NFCT module can be used to read an RFID tag such as...
Hi
Hope someone can help me with the following:
I am using SDK 17.1.0 and SES (Release 5.68). I have copied the entire SDK and all project files to a cloud-based disk...
My Nordic device (nRF52833, using SDK 2.1.2) is a peripheral. I need to periodically transfer to it large amount of data from central device over connectable Nordic UART Service...
Hello,
I am working on Find my implementation . In my project , I don't have prj.conf but prj_ZDebug.cnfg and prj_ZRelease.cnfg are there.
I want to update few configuration...
Hi,
I'm trying to create a custom board definition for our project. So far, I used the nRF5340DK's board definition, removing unwanted definitions and aliases from the DK...
I am receiving the error "qspi_nor JEDEC id [ff ff ff] expect [c2 28 17]" on device bootup. I am using the nRF52840. I have the qspi disabled in my device overlay.
This...
I just move code from main.c to other files for it is too chaos to lay them together in main.c.
I got this error forever after trying what I can image,except delete "static...
Prior to moving to sysbuild, we were dynamically settings a CONFIG_ variable in our `CMakeLists.txt` based on the board passed to west. And this was working fine.
if...
I've had trouble getting the MCUboot to compile for our application which runs on the nRF7002DK board, and I have similar trouble with the Lesson 8 examples on the nRF7002DK...
I have searched this website,there is only 1 post,but that is not my scenario.
I think this is a normal use case:
There is a struct:
I want to allocate a queue for...
Hi!
I have a bootloader using SPI 3 for a bootloader LCD animation. Unless I attach an RTT console, the animation causes my DFU to fail 100% of the time. It is making me...
Hi,
Since I want to flash the factory data later, I don't want to use the default certificate. I set CONFIG_CHIP_FACTORY_DATA_BUILD to n in prj_release.conf , but a compilation...
Hi Sir, We are planning for a Hardware deign by using nRF52833 and we are stuck on what should be suitable the supply voltage. In some case the data sheet showing that it...
Hi there,
I'm encountering an issue while trying to flash a PWM example built with NCS v2.9.0 on Windows 11 (using Python 3.10 ). The build completes successfully and generates...
