I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
This is odd, one thread can access i2c API just fine.
Another tread the same API call causes Secure Fault.
(These threads are mutually exclusive btw), the environment...
Hi,
I am trying to get the GPS coordinates from nrf9160 devkit so far I am following this guide . I was successfully able to get the coordinates once using:
However...
I have implemented a ublox ANNA-B402 on a custom board and am trying to flash code using the debug out header (P19). I am using Segger Embedded Studio and am flashing code...
Hi,
I have twp device: one peripheral and one central. My peripheral is sending out high payload data continiously. And my central is sending data ()in 10Hz frequency. However...
Hello,
I'm interested in increasing the range I can get out of an Isochronous connection between two nrf52832 while maintaining about the same throughput. I'm not concerned...
Good morning,
In our next product (mounting a nRF52840) we will need a dual UART+BLE update channel. We have already implemented the update via BLE and we are now trying...
In SDK v2.6.1, commenting out the following code in websocket.c allows successful connection to the WebSocket. However, in SDK v2.7.0, even after commenting out the same code...
Hello! I have a Nordic nRF52840 BLE dongle, and I want to scan/sniff BLE air using custom BLE parameters: scan window and scan interval. How can I achieve this correctly?...
Hello,
I'm trying to figure out why GPIO 26 and 27 on the nrf9151 DK default to HIGH. I have my SALAE USB scope connected to several pins. When the board resets, only GPIO...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
I would really like to use Bluefruit and make a Long Range connection between Servers and my Central. I know that it is not build in Bluefruit by default, but there must be...
Hello!
I'm using BLE Mesh sensor client receiving messages sent from multiple sensor servers. I used 2 nRF54l15DKs as 2 sensor servers, each sending 9 16-bit float data...
I have a problem with connecting to my device after i disconnect from it. I have tried ubond function, it does not work. This is my disconnect function:
I have a service...
