Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Just upgraded to NRF v 2.6.0 (Mac OS; VS Code). Our code previous built and ran successfully on our custom board with v 2.5.0 of the SDK.
Now we get the following error...
Hi all,
I'm developing a project on top of nRF5340. Thus I created a custom board definition in my project area:
That is a direct copy of ncs/zephyr/boards/arm/nrf5340dk_nrf5340...
Hello,
we are trying to use the nRF9160 as a serial modem for a Raspberry Pi running on Debian.
The application is basically the nRF sample "nrf\samples\cellular\modem_shell...
Hi,
I'm trying to build the Serial LTE Modem in my nrf9160 SIP custom board to communicate the STM32 MCU with the nrf9160 using AT Commands via uart.
My physical connections...
Hi,
I created a custom service in accordance with NUS service. I am able to assign all handles, subscribe to notifications. But I am not able to read any data from the device...
Based on my understanding on SPI signal, CS/SS pin need to pull down to low when read/write and pull up high when the action is finished.
May I know if this feature has...
I'm currently working on a project that uses the MLX90640 IR sensor. By default, this device has an I2C address of 0x33, but it can be set up with one of 127 different I2C...
Sifting through previous posts about redirecting printf to uart by using retarget.c, I have found this will work on previous versions of segger (5.42). Has anyone gotten it...
I tried adding the following settings to prj.config
CONFIG_CHIP_OTA_REQUESTOR=n
CONFIG_CHIP_QSPI_NOR=n
I've also tried to modify the Devicetree to be the qspi part in...
Hello, I have a project sampling a ADC. It has a INT output signaling new data is ready to be read with max sampling rate of 125ksps. I am using the interrupt and then reading...
Hi community,
I'm making a custom board using the NRF52840-CKAA. I'm trying to make a Bluetooth application for this board but struggle to achieve it.
setup:
- Visual...
nPM1300ek version: 0.9.0 I have both "nPM Controller" and "USB PMC" USB connected. I tried powering USB PMC through the computer and also tried a "Wall Wart USB".
I have...
Hi,
I have a device which has different UUID s for the write and read characteristics than the Nordic devices. The device I want to connect to will give out sensor data...
hi,
I am in the process of creating a board definition for a custom hardware we are proptotyping. I follwed the instructions in the intermediate course, copying the nrf5340dk...
I have a device which advertises some services, I want to discover those services and write to those characteristics. However I can only find one service and not multiple...