If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
I've seen this discussed a few times before, but haven't seen a great answer on this. It seems to be commonly known that attaching a debugger while using the IEEE 802.15.4...
We want to measure latency and PER between two OpenThread Nodes exposed to WiFi interference. Multiple Raspberry PIs, which are configured as AP and/or client, simulate flooded...
Hi,
I have been trying to get Periodic Parent Search active on my nRF54L15DK (and also on an nRF52840DK) without success. My approach has been:
Use the OpenThread CLI...
We are currently using the STM32WL5MOC module and are facing a serious issue with LoRa range. The communication range is not going beyond 1 meter, and the RSSI while receiving...
Greetings,
I have set up some tests using the ZTest environment based on the test sample in ..\v3.0.2\zephyr\tests\bluetooth\adv\. for my custom project which has custom...
Hi,
We are considering using nRF54L15 / SDK3.1.1 -> as a wearable device that is part of a Thread network. We also need to do sporadic BLE connections and channel sounding...
We've a nRF9151 DK for which we built the Nordic Semiconductor LwM2M Client sample using SDK 3.0.2 (modem firmware 2.0.2).
We followed all steps listed in https://docs.nordicsemi...
We are seeing network issues in some particular locations. In these areas, the device is unable to connect to the cloud.
Hardware: nRF9160-based board
Modem firmware...
I am running the boot loader with the default name 'DfuTarg' on a Nordic NRF52840 board very similar to the PA10056. I download this boot loader to the board, connect to it...
I am working with a product that uses the NRF52840 MCU and operates as a BLE peripheral.
I would like to know if the Cortex M4 in the NRF 52840 has support for programmable...
I am using VS Code to develop on the nRF52832, which is externally connected to a TCAN4550 CAN-FD chip. I successfully used the tcan4550evm.overlay to send and receive 8-byte...
Hello Nordic Support,
I am trying to use the nRF5340 SDK to communicate directly with the network core via HCI commands , without going through the application core.
Steps...
We want to use the NRF52810-QFAA-E-R7 in our device. Its only function will be tunneling data from UART to Bluetooth and back. No other functions are needed. What is the minimal...
Hi guys, I am trying to enable timer interrupt in nRF54L15.
but when i debug the application it locks inside the IRQ_lock.
can anyone explain me the issue here. It would...
Hi Nordic Support Team,
I am currently working on integrating the MAX30001 ECG/Bio-impedance sensor with the Ezurio nRF54L15U DK (nRF54L series). I am using the nRF Connect...
