I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
I've recently received a custom board I've designed and am programming with the nRF52DK, following the procedure in L3 E1 of the SDK intermediate course. I've flashed the...
Dear Nordic FAE Team,
I am currently developing a low-power Bluetooth product based on nRF54L10 , and I have an urgent requirement to optimize the System OFF mode sleep...
Hi,
We are currently in the hardware design phase and comparing different Wi-Fi antennas to find the best one for our product.
Right now we test using: - Scan sample ...
Hi
We currently have products in field test that disconnects from network and never reconnects. It only occurs to a few devices and not all. Restarting the device works...
Hi,
I am using nRF54L15 with Zephyr RTOS in nRF Connect SDK v3.0.2 .
After performing a FOTA update , the device reboots. I need to retain the state of a GPIO pin across...
The 54L15DK has two issues. First, what is the purpose of the 3.9pF capacitor on the reset line? If it's for suppressing glitch signals, isn't the capacitance value too small...
I am using nRF Connect SDK 3.2.1 and Toolchain 3.2.1. The hardware I am using is the nRF52840DK and a custom board with the Raytac MDBT50Q-P1MV2 - which contains the nRF52840...
Hi everyone, I’m updating a Matter attribute:
I’d like to know if there is any callback or event that confirms when the attribute report has actually been sent by the...
Hi,
I'm looking for help with an Android DFU failure involving an old nRF51 Legacy DFU bootloader.
Setup:
- Bootloader: nRF51 Legacy DFU v0.8 (SDK 9.0)
- Firmware...
I am at the breadboard stage of this project using an nRF5240DK and various sensor evaluation boards. Additionally, I have an embedded SDCard connected via SPI. The firmware...
We designed a nRF54L15 custom board with a nRF21540 FEM and nRF7001 Module which are on the same SPI with separate CS pins our device tree is configured for this as follows...
Setup
SDK/OS: nRF Connect SDK v3.1.0 , Zephyr v4.1.99
Board: custom board
Summary I am measuring the time from reset (or power-on) to the first user code...
hi,
i'm learning this exercise and when i build and flash the exercise it works perfectly but then after i see this errors in the terminal
and after that i create the...
When using an onomondo softsim with all security features etc enabled, and using fota on external flash. nrf9151DK. NRF V3.2.3.
How is it possible to make changes to the...
