Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hello,
I’m currently working with a custom board based on the nRF9160 SiP, and I would like to measure the LTE-M TX power after the antenna impedance matching circuit. Ideally...
I am using the nrf52840 chip on a custom made PCB that is powered by a USB-C which provides it with 5V.This 5V is then converted to 12V using CH224K which then is wired to...
Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
Using wireless sensors with nRF54L15, the sensors do not need to be connected, only broadcast a small amount of information. There will be 50-60 thousand nodes, and they are...
Hi, I'm trying to setup serial recovery in my project, in order to update firmware via USB cdc-acm.
I'm following this exercise from the academy which seems what I need...
Hi. I can't build the hello_dect example using cmake, the build process is failed with the following error: In file included from /home/cybermag/ncs/nrf/modules/trusted-firmware...
Hello!
I am interested in the Non-IP Data Delivery support in the nRF9160 module. In the description of AT commands, I did not see an opportunity to set PDP-type="Non-IP...
We use a module like EC2832AA1. I checked that nRF52832-QFAA-R is used for this module. This module has ap-protect enabled. So I added the command "nrfjprog --recover" to...
Hello!
We have developed a product that we would like to add some testing for and I have looked at both ztest and unity testing. Currently I am struggling with running the...
I have tried using SMP svr example with MCUboot for FOTA, NRF Connect SDK version 2.9.0. The example is located in zephyr\samples\subsys\mgmt\mcumgr. This example is working...
Hi, I have develop a project nRF5340 + W5500 Ethernet IC
Last time I develop a code with nRF52840 + w5500 and work success, but this time the same code work with nRF5340...
Hi,
I am currently trying to work with pairing and bonding between the peripheral and Central device.
I am using two nrf52840 dk one as central and the other as peripheral...
Hi,
I cannot start HFXO on nRF52832. I'm using 32MHz crystal TSX-3225 32.0000MF20X-W0(from Mouser) wtih 12pF caps UMK105CG120JV-F(also from Mouser).
Checked with beeper...
Hi everyone,
I'm trying to set the USB polling rate with the nRF52840 and it seems like I'm stuck at 8 to 9 ms polling (~125 Hz). I'm using the Zephyr hid-mouse example...
