Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi all,
I asked this question before but I am not able up to now to find solution. How to use DFU example of SDK 7.1 for the S130 SoftDevice. I have tried some flash address...
I am currently developing a bootloader for N548 chip from Dynastream/Nordic.
I am following the project example for the S310 soft device and using IAR.
The project had been...
So I see ble_app_hrs and others have some nice examples of buttonless reboot into DFU bootloader. But for security reasons, I'd rather the user hold down the reset button...
hi, I am very new to ble and I am trying to download softdevice S110 to my Yunjia NRF51822 board. I am using J LINK connected to my linux PC to download the softdevice to...
Hi：
I used a design with nRF51822-QFAA+BAL-nrf01D3+Pi-network+SMD chip antenna,but it didn t work well.I tested the VDD_PA Pin ,it didn t have a 1.6V voltage(datasheet),that...
Hello,
I am trying to adapt a bootloader from sdk examples to my nRF51822 board without success.
I am able to adapt the example apps from the SDK (I have to change the...
I want to use ble_app_multilink_central example but can't work.
NRF1422
QFACA10
PCA10028
already program softDevice S120 and use Keil C to download ble_app_multilink_central...
I'm trying to use gpreg for state across toggles of nRESET. I thought it was working, but when I tested it on hardware without jtag connected it seemed that gpreg was getting...
Hello,
Finally, after some struggle, I achieved to port the bootloader to s120 V2.1.0 and work just great on a dev. board with nRF51422. But now I have another problem...
Hi, i hope i'm not duplicating any questions, but i couldn't find a similar one.
I worked with other ARM micros in both mbed and Keil before, but i'm new to Nordic Semiconductor...
Hello,
I getting started with nrf51 DK.
I followed with many blogs.
I checked errors, and fixed. And I builded the example 'blinky'
But my nrf51 is not blinked.....
Hi all,
I am doing the PTS and meet some issues here:
Using the SDK 8.0 KB demo with SD8.0;
Do the profile test with PTS dongle and tool, and return errors on...
Hello everybody,
I'm using NRF Beacon (51822) board, sdk 6.1.0.0 and s110, problem is when I enable whitelist and add the Bluetooth address of my phone( 74:51:BA:F7:60:9F...
In my bootloader I'm using sd_flash_page_erase() directly without pstorage.
The flash erase performance is exceedingly slow. It is taking 13.187 seconds to erase 132 pages...
Hello!
We are thinking about creating some devices for Apple HomeKit.
But devices for HomeKit have to go through one thing: Apple certification. And one part of the certification...
