Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello
Our 52840-based device has a functionality of playing one of 10 pre-recorded phrases via I2S interface. We'd like to be able to update the wording or load a different...
When integrating DTM into my main app, I have to comment out the macro CONFIG_BT=y to ensure the DTM test can run properly after the build. Are there alternative ways to include...
Hi
I am working on nRF54L15-DK (PCA10156 0.9.2 2024.49) with chip N54L15 QFAAB0 2444AA
I am using Nordic SDK 3.0.2 and Zephyr 4.0.99
My task is to have the top 2K of...
Trying to read button 3 on the npm1300-ek, which is gpio 1 according to the schematic. The following #defines represent the gpio related registers on the npm1300:
#define...
I have been using my nRF54L15-DK board since it arrived just fine, however today when I went to flash the firmware I received the following error:
-- west flash: using runner...
Dear All, I am looking to connect to WiFi enterprise AP. So far I have been able to connect to the network using the nrf/samples/wifi/shell using a command that looks like...
Setup: SEGGER and running S112 & nRF5_SDK_17.1.0
Don't want to delete all bonds, only the specific one.
Bonded with Android and Apple smart phone
Delete pairing information...
Hi there.
Does the nRF52840 require any protection on the Bluetooth Antenna Line needed to block large unwanted signals when fitted on a Modem that also incorporates GSM...
I am using the u-blox NINA-B410 in BLE Central mode to scan for nearby devices. It only detects BLE-advertising peripherals (phones running BLE advertiser mode, BLE watches...
Could you please clarify for the clock and oscillator setup, are the LFXO oscillator and LFRC RC oscillator internal oscillators on the chip? Or is an external oscillator...
In the devzone there is a list of the "Recent and unreplied" posts, but is there a way to just browse all the devzone posts? Not just the "Recent and unreplied" list.
I...
I am debugging an issue where my nRF9160 (NCS 2.7.0) rolls back to the previous firmware after a seemingly successful upgrade. I am not getting enough logs from MCUboot to...
I was in the process of evaluating a driver when I noticed I2C communication was not working as expected. I put a probe on the relevant pins and noticed the Voltage on my...
Dear Nordic Specialist,
I would like to ask about the correct usage of the power recommendation parameter in the channel sounding configuration.
In bt_le_cs_set_procedure_parameters_param...
Hi，
Recently, I encountered a problem.
I wanted to set a MAC address of type BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE, with the upper two bits set to 11 as well...
