Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi,
I have trouble configuring Here service for multicell positioning. I've used the service before, but recently updated to NCS 2.0.0. I don't know what are the configuration...
Hi,
I'm trying to send a saadc float value over ble (dk to dongle) with ble_nus. I'm getting the right values but also some other stuff in addition. How can I filter this...
I need help with the minimal circuit board requirement of the custom board with nRF52832 and nRF52840 for wireless and SPI communication.
I need to read vales over wireless...
Hello !
Do you have any evaluation results for nRF21540 DK in case of real connectivity range ? Just some typical digits what can be seen easily.
I have own radio and...
I am trying to setup and run the existing scripts, which are part of pc-ble-driver-py.
The following are the steps and tools
1. Installed the pc-ble-driver-py pip install...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
Hi,
I have a custom board with nRF52840/SDK 16/Softdevice 7.3.0 using Secure Dfu Bootloader. On my Android device I use Nordic Dfu Library. I have tried all available Dfu...
Ever since the toolchain manager v1.0.0 came out in the nRF Connect software, I have been unable to download it. I keep getting this error:
Any ideas?
Thanks,
Jow...
Hi
I am using SDK 1.9.1 with VS Code on MacOS to develop for nrf5340. I also have a nrf5340-DK board.
I am having problems finding the right includ file for using the...
I'm new at this (so be gentle). Trying to understand the process for activating a SIM card with Verizon using the NRF9160. I see that this modem is approved; so do I only...
Hi, I want to add CLI in our current firmware. i found a way to do is Zephyr shell. our firmware is based on aws iot sample and nrfconnet sdk1.9.0 after integrating zephyr...
According to data sheet of nRF52832, internal pull up resistance is 13kohm. Can we find the 13kohm internal pull up resistance in the code and can we change that internal...
Ideally we should not get any data when internal pull up resistors of nRF52832 board are disabled and external pull up resistors of SHT 40 Slave sensor are disabled. But I...
Hi,
I haven't been able to actually find out if the VBUS can be used to drive the DETECT signal to go from system off to on mode.
Are there any examples on how to configure...
Hello All, We have designed a custom board for our product and everything pretty much works fine. But now that we have decided to stick to WebBLE, we are facing some issues...
