i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
My understanding is that when the module's measured RSRP is lower than that defined in the broadcasted SIB, ECL will be escalated to higher level during RACH process.
Besides...
Hi,
I found out that my Matter device does not commission to Alexa because as part of adding the device Alexa will try to read FeatureMap attributes from all clusters and...
Hello! I'm working on some project using Fanstel BM832 module. I'm using the configuration based on board nrf52dk_nrf52832, with some minor modifications (led's and button...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
I have a quick question about configure i2c.
I have the following schematic:
And the following configuration for the nrf54l15 :
And the following in prj.conf:...
Once the nRF52840DK is running the Zigbee light bulb demo I cannot flash new code to it unless I disconnect the board and reconnect it first.
I am using nRFConnect for Visual...
Are there user programable once registers on nrf5340 that I could use to store board hardware version? I looked at UICR, but I think they get erased when the whole chip is...
I added FOTA over Bluetooth to my NRF52840 application. Everything works, I can update the application over bluetooth and it runs properly, but after updating if I unplug...
Hello Nordic support,
I would like to understand how I can decrypt the packets that is using Legacy passkey pairing. Here is the BLE sniffer log, where I selected Legacy...
Hi my ffriends,
I’m working on a wireless system called for me " Wireless Link Project" , based on the nRF24L01 (non-Plus) transceiver.
I have two identical boards using...
Hello DevZone,
I have a confusing question about TF-M. Need help from a TF-M expert.
In this document , it says that we must disable uart1 in non-secure application, because...
I'm trying to test the overall pwoer consumption of my setup (nPM1034EK and nRF54l15DK) using the PPK2. As I've started this, I've gotten far higher numbers that I expected...
After I reset the kit (custom equivalent to nRF52DK) it advertises, and I can connect from the BLE Standalone App on my Windows computer. But it only advertises for a short...
I recently bought a fanstel blg840 device, and I have programmed At client firmware in nrf91 and custom code into nrf52, but the problem is nrf52 is sending at comments to...
