We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
I see from the SAADC page of the datasheet that there is an internal 0.9V reference on the nRF54L15, but I don't how this reference is generated. Is it an active regulated...
Environment
My hardware is the nRF9151DK dev kit and a custom board with nRF9151 (Monkeytronics Airsmart Cellular Beta 3).
Using nRF tools and SDK v3.1.1.
Using Onomondo...
I used nrf54L15 chip P2 port's SPI.used spi_transceive_dt tx 10 bytes. but chip divide two process (8Bytes+2Bytes).this result is not my object. code as below:
int spi00_dma_transceive...
Hi, The RebootCount attribute of the GeneralDiagnosticsCluster is returning a FAILURE response.
This issue is causing failures in Matter test cases TC-ACE-2.1. CONFIG_CHIP_LAST_FABRIC_REMOVED_ERASE_ONLY...
Hello,
I'm trying to put the nRF54L15DK into System Off mode, using sdk & toolchain version v2.8.0.
The provided example (\samples\nfc\system_off) works on my evaluation...
Hello, modem_shell sample build throws error “undefined boot_write_img_confirmed” with nRF Connect SDK 3.2.1. This issue didn't exist in nRF Connect SDK 3.1.0. I did a quick...
Hi I have updated th nRF Connect for VS Code Extension Pack to the newest version. But when I want to enter Debug in VSCODE, the error comes out. Before upgrade, the debug...
Hello,
I am currently working with an nRF5340 configured to operate in High Voltage mode , where the main input supply is 5 V .
Issue description
When the nRF5340 is...
I just wanted to notify that I need to set CONFIG_SOC_NRF_FORCE_CONSTLAT=y in order for a NRF54L15 to be able to respond as a SPI slave (SPIS) using nrfx SPIS code.
Otherwise...
Hi,
I have developed custom hardware based on the nRF9151 chipset.
I would like to program the firmware using nRF Desktop (Programmer) with a third-party SEGGER J-Link...
Hi,
I am having trouble communicating between the nRF54L15 and the nRF7002 in a custom board. I flashed the scan sample. I made a new overlay as below:
/*
* Copyright...
Since about a week or two ago, I cannot flash (or debug/reset etc.) my device from the VSCode nrfConnect extension, when more than one device is connected to my PC. I am using...
Hi,
I am trying to confirm whether nRF54L15 as a chip officially supports the UTP OTA feature.
From the SoftDevice Controller documentation I can see that the following...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
