Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
Hi,
I have twp device: one peripheral and one central. My peripheral is sending out high payload data continiously. And my central is sending data ()in 10Hz frequency. However...
Hello,
I'm interested in increasing the range I can get out of an Isochronous connection between two nrf52832 while maintaining about the same throughput. I'm not concerned...
Good morning,
In our next product (mounting a nRF52840) we will need a dual UART+BLE update channel. We have already implemented the update via BLE and we are now trying...
In SDK v2.6.1, commenting out the following code in websocket.c allows successful connection to the WebSocket. However, in SDK v2.7.0, even after commenting out the same code...
Hello! I have a Nordic nRF52840 BLE dongle, and I want to scan/sniff BLE air using custom BLE parameters: scan window and scan interval. How can I achieve this correctly?...
Hello,
I'm trying to figure out why GPIO 26 and 27 on the nrf9151 DK default to HIGH. I have my SALAE USB scope connected to several pins. When the board resets, only GPIO...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
I would really like to use Bluefruit and make a Long Range connection between Servers and my Central. I know that it is not build in Bluefruit by default, but there must be...
Hello!
I'm using BLE Mesh sensor client receiving messages sent from multiple sensor servers. I used 2 nRF54l15DKs as 2 sensor servers, each sending 9 16-bit float data...
I have a problem with connecting to my device after i disconnect from it. I have tried ubond function, it does not work. This is my disconnect function:
I have a service...
Hello Nordic support,
My application is based on nRF5 SDK for Thread and Zigbee v4.2.0, with Softdevice S140 as I want my application to operate in either in BLE or Zigbee...
I'm trying to setup an SPI communication between an EVK of the Intan RHD2216 and the nRF 52840.
Browsing similar issues, I read the following topics already
I apparently...
I've been using the following SPI1M pins and they've been working:
But I have migrate away from these pins due to production PCB layout problems. The pins I need to...
I'm using nRF Connect SDK v2.7.0 with v2.7.0 toolchain to program a device with nRF52840 SoC.
When configuring task watchdog timer with hardware fallback an assertion fails...
