I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi guys,
I am experimenting with OTA buttonless DFU.
I included the Buttonless Secure DFU Service to my application and I managed to flash the new image over the air through...
Hi there,
As the title says, I only get an all white window whenever I open an app in nRF Connect for Desktop (this happens for all apps).
If I try to reload the window...
I try to get the Direct Test Mode App to work on a Windows 10 Notebook. (for System Details see attached system report and verbose logfile).
Software versions:
nRF Connect...
Hello,
I'm using the PCA100095 NRF5340 development board and developing with the NRF Connect extension for VSCode v2022.3.104 .
When attempting to use the CMSIS intrinsics...
Hello,
In my project i am using nrf52840 with custom board, here i am using BLE UART to send the data from the mobile to device and sending data from another sensor board...
I would like to add Just Works security to our battery service (BAS). However, I could not find such a setting anywhere, so I looked into it and found that in bas.c BT_GATT_SERVICE_DEFINE...
I am troubleshooting a board with no working RF. On looking deeper it appears that the HFCLK is not starting (NRF_CLOCK->EVENTS_HFCLKSTARTED is never set).
This is on a...
Hello,
I am currently working on the NRFX QDEC library with a decoder to be used with a servo motor.
We manage to initialize and enable the QDEC and IRQ and we get...
Hi,
I am facing a problem in adding a power down feature in my application, the details of the application are as follows,
I am using the sensor server example given...
Hey guys,
I have a small concern and decided to ask here, as i was not able to found answer neither in zephyr or nrf sdk docs (not even sure which one apply to my question...
I use the DF example.In Rx.i use both nrf52833 boards as test.i use NCS 1.9.1.
In rx,i use the silab's 16 antenna array for receving antenna array.
because it has 16 antennas...
Topology:
Raspberry Pi A Raspberry Pi B
|(USB connect) |(USB connect)
nRF52840 dongle A )))) Thread (((( nRF52840 dongle B
Software:
nrf52840-dongle: ot-rcp.hex...
In the online power profiler for nRF52832, when I look at the advertising (Tx/Rx) power consumption I see that if I set the Tx payload to 0 bytes the Tx time modeled is 128us...
Hello,
In my project i want two use two UART as off now i am using app_ble_uart example since by default 6,8 is tx and rx pins respectively. so overall application of my...
