Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hi all,
I have set up an nrf52840 as the sniffer to sniff the connections between my custom board and central phone. My goal is to figure out the bottle neck of the ble...
I based my project on the secure wireless uart example in the nrf5 SDK and linked to the precompiled gcc library 802_15_4_lib_gcc.a
I then tried to add multiple entries...
It seems that once we install nRF Connect into VS Code it completely takes over and now when I open any file in VS Code I see all of the nRF connect tabs and controls which...
I'm trying to debug an application however there is no documentation on how to set up the debug.
How come nRF connect is selecting the HEX file. I want it to select the...
Hey,
I am trying to use the Jam Detection Feature of Openthread on my nrf52840 DK. The device is running as coap server with the example code
"simple coap server". I...
Hi All,
I'm using SDK17.1.0 and I have a question about pairing.
I have a project that references the ble_app_bps program, but I don't get pairing notifications when...
Hi All,
I have a question, it seems to be the SES debugger crashed.
My project only uses peripheral devices, my purpose is to combine libuarte with my framework.
And...
I want to send an interrupt instruction from appcore to netcore by using IPC.
Implementation code in appcore:
Implementation code in netcore:
However, in actual...
I have a vendor mesh model that needs to send a custom 8 byte message.
Here are some definitions
BT_MESH_MODEL_PUB_DEFINE (vnd_pub, NULL , 3 + 8 ); <--what is with this...
Hi,
I have a nRF52840 Dongle connected up to an external j-link debugger. I have been using this over the past few weeks with no issues and unfortunately I have managed...
Hello,
We're facing an issue related to the USB IRQ.
I've 2 EVK boards NRF52833 (let's call them EVK_1 (PTX) and EVK_2 (PRX) respectively). One of them ( EVK_1 ) is connected...
Hi!
We're developing a solution where we use PC-BLE-driver JS on our central side, along with BLE dongles with nRF52840 chipsets. These dongles are pre-flashed with a connectivity...
The previous ticket was closed unexpected, https://devzone.nordicsemi.com/f/nordic-q-a/87224/how-to-remote-control-nrf52840-led-s-on-off-through-openthread-network .
Thanks...
Hi All;
i am using nRF5 SDK 17.1.2 / 17.0.1 and examples are ble_app_uart & ble_app_uart_c and nrf52833. Mode is connectable and coded phy .
I tried to connect the devices...
Hello,
Hi i am working nrf52840 DK board, from this first i have load softdevice and after that i flash the code so that time it was showing the error as "Error Flash...
