I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well. ...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
I have a project where I use nrfx_saadc and need to change channels and simple/advanced mode in runtime
If I start with simple mode, samples, move to advanced mode...
This is my environment:
IDE: VSC
SDK: NCS v2.2.0
Central - iOS or Android phone running custom App, or an nRF52832 on custom hardware
Peripheral - nRF52832 on custom...
The note in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.5.0/nrf/security/tfm.html#overview reads: "Support for TF-M with minimal version disabled in nRF Connect...
Hello,
I flashed the audio application as left headset on my audio DK, but whenever I connect it to my mobile phone, the device isn't shown in the media output list.
Yes...
We are trying to setup image encryption in our nRF build, for use with BLE DFU.
I see that this is not supported by Nordic, but that there is support for it in MCUBoot....
When using the nRF5 SDK v17.x development environment, the BLE MAC address can be retrieved using:
This will return the assigned MAC address (eg. from the nRF52840 on...
Hello,
I am currently working on a project using the NRF52 SDK and Segger Embedded Studio. I need to set up a password (or passkey) for securing the Bluetooth connection...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I am trying to use the device name as...
I'm developing a linux device driver for nrf7002 and adding softap support. From the Nordic Playground driver it looks like there is no current support, but a lot of the cfg80211...
Hi, when I run the MQTT sample as is, I'm having problems with the TLS and port configuration. The terminal output is:
That looks correct, but on closer inspection the...
Hi!
I'm getting this error in nRF Cloud when using a nRF9160DK connected by LTE-M to the network:
Device sometimes sends some data correctly but, after few minutes i...
Hello everyone,
I have a custom board with a NRF52840 microcontroller with 32MHz crystal oscillator, running Zephyr RTOS with NRF Connect SDK and want to make use of a hardware...
I have nRF Connect SDK v2.6.1 installed on a Mac, the latest toolchain installed via nRF Connect for Desktop, and VSCode with all the nRF extensions. Everything works pretty...
I have a custom board with a nRF52832 QFAB at its center, and I want to program it via a nRF52-DK. I have created a custom board directory and have initialized a few led pins...