I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
On our NRF52840 Based product, we have enabled USB CDC Use.
We see increase of ~0.5 mA when enabling USB . We are ok with this , However - when we remove the USB cable...
Hello Nordic Team,
I am creating Scanning application using SES for NRF82532 (SDK 15.3.0 and softDevice 6.1.1), i am using app_timer_freertos timer.
application is calling...
Based on Android studio 3.0, gradle-4.10.1 compile the project downloaded from github.com/.../android-nrf-mesh-library . I get the following error:
The module 'app' is an...
Hi,
I have an external flash ( via QSPI ) working on NRF52840 Based product.
I'd like to redirect all NRF_LOG message to a file , is there a similar log backend available...
Dear developers,
My device uses the NRF52840 SoC and is equipped with a modem for internet access.
To perform firmware upgrade, I imagine I would have to download a DFU...
Hello, I tried to work with nRF52832 to read adxl362 registers, Here is my function to read all 3 received bytes from adxl362 (according to datasheets, the last byte must...
Hi,
I tried to install the latest sniffer v3.0.0 and Wireshark v3.2.0 on my computer. I could not see PCA10056 listed. If I start my wireshark from command line, with "open...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send data from sensor over bluetooth...
When i used Port 0 assigned on Uarte rx tx pin , everything was ok.
But when i changed the rx tx pin to port 1 , for example p1.00,p1.08.p1.09, it doznt work...
i am sure...
I use nrf5_SDK_for_Mesh_v3.2.0_src , nRF5_SDK_15.3.0_59ac345 and board pca10040.
Copy the ble_app_uart_coexist folder into the examples/ble_peripheral folder at your nRF5...
Hello.
I'm doing a DFU customization now.
However, because of the problem of data transmission of the last packet of the first page when advertising,
connection and...
I am setting up a relatively complex project that runs on top of FreeRTOS and it is based on the HRS freertos sample app from SDK 16.0.0. The device will need to run in several...
