I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello,
we are developing a new product based on the nRF52833 QFN40 IC.
We would like to add the nRF21540 range extender to the product and also a SPI Flash to store...
I am currently working on a project involving Bluetooth channel sounding for distance measurement using the nRF52840 dongle and nRF52840 development kit. While I was able...
Hello,
I’m using the nRF Connect extension for VS Code, and I encountered an error while trying to compile the peripheral_hr sample code.
I'm using SDK 2.9.0 with toolchain...
Hi
using nrfConnect SDK 2.9 I try to use the non-blocking SPIM example and the nRF52840DK as starting point for my application.
I encountered an error:
CMake Error at...
Hi,
Happy New Year! I hope this year brings fewer bugs than the last.
SDK Version: 2.7.0 Board: Seeed Studio XIAO nRF52840 Sense
System Description: I have a setup...
Hello.
The chip of Nordic, nRF21540: https://www.nordicsemi.com/Products/nRF21540 Is it possible to use it as a RF amplifier (PA + LNA) for a ESP32-S3 chip, which is 2.4GHz...
I am trying to transferring 9 16-bit floating point data(acceleratometer, gyro, magnetometer * x, y, z) fetched from icm20948 sensor by BLE Mesh, using nrf54l15dk. I changed...
Hi
We plan to use the nPM1100 for charging a LiPo battery and provide power to an nRF52810 processor and subsystem. The battery is very small and has no PCM.
Questions...
This is the example:
https://raw.githubusercontent.com/IRNAS/ppk2-api-python/refs/heads/master/example.py
Anything related to ampere meter mode does not seem to work,...
HI,
I am working on a NRF54L15 with NCS 2.9. I have a service my_service created with BT_GATT_SERVICE_DEFINE, with two characteristics, "Protected" and "Password". "Protected...
Hi
I am looking a simple way to synchronise multiple devices which might be in connected state(and streaming data) or not(storing data on flash).
I need an sync accuracy...
Hello,
I’m having trouble understanding Apple’s requirements for the advertising interval.
https://developer.apple.com/accessories/Accessory-Design-Guidelines.pdf
...
Hi
in NRF connect SDK is it possible to do the following:
recive one byte from PC via USB to a dev board. Immediately or with a delay less than 200 micro second send a...
I have a linux driver that uses nRF7002 am able to have both STA+AP. The issue I'm running into is that when I have STA up, AP MUST be the same channel, and vice versa. I...
