In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi! I need to understand how my board is working. Right now I'm writing code on Visual Studio Code then I flash that on my board. I need to know in all of this how I'm using...
I adding an Event to Asset_Tracker_V2. I have created bms_module_evnet.h and bms_event.c files in events folder and bms_module.c. I have defined inclusion of these files in...
Hello Nordic engineer，
SDK is 15.3.0, and example is ble_app_uart
I use the "nrf_sdh_disable_request()" function to turn off Bluetooth
Then start with the function...
Hi,
Environment: nRF SDK 1.9.1, VS Code 1.66.2
Without making any changes, I can build and flash the iso_receive sample but it fails with a -5 error code (EIO) on this...
This is a cross-post from my question on StackOverflow here . This might be a more appropriate channel for this question.
I have a custom board using the u-blox BMD-350...
Dear Nordic guys,
We are going to produce large number of BLE beacon devices and would like to label the BLE address on each device. We are using the default mac address...
How Can I store information about button port ? I have two buttons P1.02 and P0.02. I have
And I have one function to init button
the most interesting is callback...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Segger Embedded Studio 4.16
I am working...
I'm trying to run LTE/BLE Gateway sample on nRF9160DK , i followed all the instruction in the sample instructions.
The Jlink RTT for nRF52840 and LTE-Link Monitor logs are...
Hi nice people, I am working on developing using visual studio and Make environment. I am trying to function UART tx/rx interrupt works but no luck. The TX and RX works perfect...
Hello, I've been trying to launch zephyr SPI example, but I'm having issues with SPI sending anything. The code itself does not throw any errors, and it seems like my board...
hello sir ,
i am using thigy91 board and uploaded the asset tracker application code from ncs sample code . ii am getting humidity data on my azure cloud .but there was...
Hello everyone!
We are using nRF51822 SoC together with s130 Softdevice. nRF5 SDK v12.3.0 is used for firmware development together with the Segger Embedded Studio.
Among...
Hardware: nrf9160DK Modem FW: v1.3.1 We have been evaluating and configuring our proprietary application for NB-IoT, which is initially designed for LTE-M (CAT-M1). The Application...
Hello,
I'm using a central device that lists all nearby peripheral devices by their MAC addresses like so:
but I also want to list the names of the devices as they...
