hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello,
I've recently was checking out the Zigbee Weather Station application running on the Thingy53 and have spotted a weirdly formatted log message regarding temperature...
Hello everyone, recently I received a thingy:91x with an extra truphone sim card.
I am based in Indonesia and want to test the cellular connection from device but doesn...
I built the demo zephyr/samples/bluetooth/hci_usb for my nrf52820, and it worked well.
But when I tried to read its manufacturer name by using command `hciconfig -a`, it...
Hi there,
I want to capture all the logs made by Zephyr and printk() calls. I want to forward these logs via USB using our custom application protocol for debugging purposes...
Hello folks,
I need some help troubleshooting a BLE antenna issue on our custom nRF52840 PCB . Any insights would be greatly appreciated!
Issue:
BLE sometimes advertises...
ncs v2.9.0
nRF52832 DK (NUS central)
nRF52840 DK (NUS peripheral)
1) When connected, see the empty PDU from peripheral to central about 100ms interval.
2) To use...
I'm trying to add an Aquara temperatur sensor to Zigbee shell running as coordinator on a 58233DK.
Regarding the logs in the serial terminal, it looks like the network was...
Hi,
I am using a nRF9161-dk with the nRF7002-ek shield WiFi tracking.
Using the nRF Connect Quick-Start, I downloaded the nRF Cloud Multi-service application and went...
I'm new to Nordic technologies and ML MCUs!
Does the ARM Cortex-M33 core, nRF5340 audio DK devkit, without any other board od periferic, support edge impulse ML? If so...
We tried connecting a deeply discharged lithium-ion battery to the nPM1300-EK to see how it would charge, but we weren't allowed to enable charging as we got the following...
NCS 2.7.0 nrf52840
I noticed in i2c_nrfx_twim.c there are some calls to pm_device_runtime_get, while in another thread ( thread ) it was mentioned that Nordic is no longer...
Hi,
we have nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin
build for CPURAD
PC: Windows 11 Pro
I'm trying...
NCS 2.9.0
nRF52840-DK
Using the OpenThread CLI example.
After turning on the TCAT function, when using MeshCoP Commissioning, the joiner will experience a system failure...
Hi, we have a NPM1300 chip connected as I2C slave to a nrf5340, acting as I2C master. Everything works fine, but there is a small detail in the NPM user manual that I would...
Hello, We have created a new product with the nRF52805 "Raytac" Module under nrf5 SDK v17.0.2. We are planning to do the CE certification soon. would like to verify a few...
