Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hey all!
I've just received my first board with a Nordic chip. More specifically it features the Ezurio BL54L15µ module.
I am currently "limited" to programming via SWD...
hi
I am using periodic_adv_conn and periodic_sync_conn from the NCS 3.0.0 SDK.
After periodic_sync_conn reports data to periodic_adv_conn in the corresponding time slot...
We are considering to develop an embedded device that can control Matter door locks. So it should act as a Matter Door Lock client. Unfortunately it is impossible to find...
Hello Team,
I have added the LittleFS file system for the external flash and am able to program the .bin files through code by keeping the bitmap array within the application...
Hi All,
I would like to know if the reset can configured to trigger by "failling edge" rather than "rsing edge" of the reset pin / configured pin?
Per the datasheet from...
While debugging the NCS 54L15 ESB module, I observed some anomalies when measuring the radio interrupt signal. For example, after the RADIO READY event is generated, it should...
Hello,
We are working with the nPM1304-QEAA-R7 in a power management application and would like guidance on how to implement or connect a fuel gauge to this device. Specifically...
Hi I could not program the device via OpenOCD (current release) The programm tells me "invalid subcommand "write_image erase prog.hex" I modifed the nrf54L.cfg
added "flash...
I have a Power Profiler Kit II and have been using it for a few years without issue. I have been using it through the nrf Connect for Desktop software and the Power Profiler...
On the nRF54L15, is it possible to configure MCUboot so that the secondary image slot is stored in external flash connected via the SQSPI interface instead of internal flash...
Hi,
We're looking to integrate the NPM1304 in a product with a very small battery. As per the NPM datasheet we've selected a battery with a PCM.
We've previously seen...
We have a production system based on asset_tracker_v2 in V1.7.0 and V2.5.0. it normally connects and publishes fine 24/7. we have many sensors in the field. There are time...
Hello Nordic team,
I have a retail Thingy:91X device. IMEI: nrf-359404230239544
It connects to hello.nrfcloud.com, but I cannot add it to my own nRF Cloud account because...
We currently have a self-developed development board with NRF5340. The example program uses Bluetooth transparent transmission. Now I have added a GPIO pin: en_power is set...
