In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I am setting up our production facility in India. Brought out our test jig software that flashes the nRF53 modules.
I use nrfutil to program the boards via "nrfutil device...
Hi,
I am using "nrfutil" v8.1.1 and "device" 2.15.2
If I have my Otii ARC plugged into USB, then "nrfutil device list" crashes nrfutil with it complaining about "serialport...
After moving from nrf9160 to nrf9151 on our prototype, our old firmware resets while trying to set up the LTE connection (this still happens when `CONFIG_RESET_ON_FATAL_ERROR...
Hi,
I am following the below link to enable the FOTA over BLE in our custom project. I have tried the "Peripheral lbs" example and it is working.
https://academy.nordicsemi...
I have programmed an nRF5340 DK with the Auracast Broadcast Audio Source application. I have a pair of Samsung Galaxy Buds3 Pro paired with a Samsung Galaxy Tab S11 running...
Hello,
I am creating my own board with a nRF5340. I see a development board with a PCB antenna. I do not have the thousands of dollars for the simulation software. What...
C:\nRF5_SDK_17.1.0_ddde560\nRF5_SDK_17.1.0_ddde560\examples\peripheral\spis\pca10056\blank\ses project is giving me the errors listed bellow when trying to run the example...
Dear Team,
I have nRF54L15-DK and my firmware is running fine over there.
Now I want to use nRF54L15-DK to program & debug standalone NRF54L15 on a my custom board....
Our existing product (already in the market) at Element Science in San Francisco, CA, USA uses an nRF52832 (BMD-350 module by u-blox) and nRF5 SDK 15.3 as base for the firmware...
Hello, I have two nrf52840-dongles which I am using to test ESB. (NCS 3.1.1)
With a few modifications to the ESB prx and ptx samples:
Remove logs except for PTX ESB_EVENT_RX_RECEIVED...
I upgraded my sdk from 2.6.1 to 3.1.1 and after resolving a few issues everything was working just as it was before the upgrade except for MCUmgr. When I run the MCUmgr client...
Hi,
I recently migrated a project from NCS v2.x to NCS v3.x and noticed that the method I previously used to generate a device-unique identifier no longer works the same...
I've seen similar threads but haven't yet found an answer that works for me. I don't know much about encryption but I've been tasked with adding 256-bit AES GCM to our project...
On a BLE Peripheral NRF52840 built with nRF Connect SDK v3.0.2 , high-rate GATT notifications sometimes push the stack into a state where no (HCI 0x13) events arrive for the...
Dear Nordic support:
How long is the single broadcast duration and the broadcast interval for Bluetooth? We would like to know what the duty cycle of Bluetooth operation...
