I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
I need help with the minimal circuit board requirement of the custom board with nRF52832 and nRF52840 for wireless and SPI communication.
I need to read vales over wireless...
Hello !
Do you have any evaluation results for nRF21540 DK in case of real connectivity range ? Just some typical digits what can be seen easily.
I have own radio and...
I am trying to setup and run the existing scripts, which are part of pc-ble-driver-py.
The following are the steps and tools
1. Installed the pc-ble-driver-py pip install...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
Hi,
I have a custom board with nRF52840/SDK 16/Softdevice 7.3.0 using Secure Dfu Bootloader. On my Android device I use Nordic Dfu Library. I have tried all available Dfu...
Ever since the toolchain manager v1.0.0 came out in the nRF Connect software, I have been unable to download it. I keep getting this error:
Any ideas?
Thanks,
Jow...
Hi
I am using SDK 1.9.1 with VS Code on MacOS to develop for nrf5340. I also have a nrf5340-DK board.
I am having problems finding the right includ file for using the...
I'm new at this (so be gentle). Trying to understand the process for activating a SIM card with Verizon using the NRF9160. I see that this modem is approved; so do I only...
Hi, I want to add CLI in our current firmware. i found a way to do is Zephyr shell. our firmware is based on aws iot sample and nrfconnet sdk1.9.0 after integrating zephyr...
According to data sheet of nRF52832, internal pull up resistance is 13kohm. Can we find the 13kohm internal pull up resistance in the code and can we change that internal...
Ideally we should not get any data when internal pull up resistors of nRF52832 board are disabled and external pull up resistors of SHT 40 Slave sensor are disabled. But I...
Hi,
I haven't been able to actually find out if the VBUS can be used to drive the DETECT signal to go from system off to on mode.
Are there any examples on how to configure...
Hello All, We have designed a custom board for our product and everything pretty much works fine. But now that we have decided to stick to WebBLE, we are facing some issues...
Hi,
I would like to declare my pin in output open-drain, so i use this configuration
My issue is when i declare my pin, I have an unexpected low state that occur...
Hi, I am currently getting started with the Thingy: 91 and am having trouble getting the SDK setup.
I download the file from: https://www.nordicsemi.com/-/media/Software...
