Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
We have custom hardware that includes an NRF52832 microcontroller. Currently pin 0.21 is mapped as reset pin and i cannot seem to figure out how to change this using...
I am sorry that I post my question on this forum because I cannot find a button to post.
I also use a J-LINK EDU mini to flash the RAK4631 board. During J-Link Commander...
I try to download FOTA from http server to nrf7002 over WIFI i use fota download library and initialized it ,then call API fota_download_start() then the fota_callback_handler...
Hi all, i have some problem while i try to estabilish an LTE connection . I'm using nordic n9160dk. I just search through the site, and i see a lot of topic like this , or...
Hi ,
Our custom board uses the nRF52840 chip, and we followed the Nordic official webinar 'Adding Custom Board Support in nRF Connect SDK' during development.
We noticed...
Hello support team,
I am a beginner in this environment and I am facing a problem while trying to compile my project in Zephyr for nRF52840dk board. I am trying to run this...
I am currently using a J-LINK EDU Mini to try and learn how to use an external device to flash the nrf board. I am running into trouble because I have connected my external...
Hello, I am trying to get to make error handling while getting GPS signal. so that if there is no GPS, I move to Queclocator commands to get LBS location. the problem is that...
What is the problem with this error, I think the problem is not getting #include <zephyr.h> liberary, if it is how to fix it. any recommendation is appreciated
Hello, we have a design that includes nRF9161 for LTE purpose and a separate MCU.
The power sequencing for nRF9161 is as follows
VDD1, VDD2 is supplied with 4.2V
ENABLE...
Hello,
I am using version 12.3.0 of the nRF5 SDK for the nRF51422 development board. I opened the 'ble_app_hrs' example code in IAR Embedded Workbench and successfully built...
Hi All,
I have design my customer board but after production nothing looks to work. i can program the board through the Nordic board by using debug out. even a simple blinky...
I have a BLE code, when it runs on NORA-B106 it gives me -20dB difference on comparison to nRF5340 Nordic DK.
It was not expected such a big difference, what could be the...
I have been trying to implement the wifi scan or wifi provisioning code on a module (MS12SF1) which is a combine wifi + ble module
The setup looks like the image shown below...
Hi,
I'm developing with NCS v2.6.0 for Raytac MDBT53v-P1M module, which inhibits nRF5340. I already have my own PCB with all the required HW components.
As a sanity check...
