Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
I'm trying to port a PPI application to an nrf5340. I'm quite puzzled, as it would appear there is no obvious way to achieve what I'm trying to do.
In short, I have a setup...
Hi,
I notice that every time I can only send 244 bytes per time in nus service, if I set higher I will not receive the data in RX.
But I also see that the thoughput...
Hello,
We're using version 7.0.1 of the S140 soft device. We are making a bluetooth application where the device behaves both as a central and peripheral. In peripheral...
we now have nRF52840 DK PCA 10056 , V3.0.0 . the documentation of product specification user guide available online is for v1.0 (old dk) , but not for v3.0 . please can you...
Hi folks,
I am just in the process of getting my feet wet with the nrf connect sdk and zigbee development is my ultimate goal.
I am using an ItsyBitsy nrf52840 https:...
Wireshark Windows version 4.4.5
nrfutil 7.12.0
ble-sniffer version 0.14.1
Somehow during the course of installing the nRF Sniffer, Wireshark got two interface toolbars...
Hi,
I'm working on a very high density board with the nRF54L15-QFAA (we want to prevent using a CSP) and I'm running into some routing issues. While looking for optimizations...
Hello, We faced with issue in which we are not able to get the time from the network and because we don't have time, we can't use JWT. As I understood issue is because of...
Hello everyone, I am want to write custom radio protocol for the nrf5340. I have already tried the ESB protocol. But that is somehow limited on the latency (I will open a...
I'd like to use the nRF52832 for cost reasons & I know there are different Bluetooth audio standards, which the nRF52832 does nto support the latest. I don't need hi quality...
Hi, I have a question about the WDT documentation in nRF5340 Product Specification v1.6.
Question 1:
The chapter "Reload Criteria" (7.41.1) is maybe a bit ambiguous defining...
Hello,
I am using the LTE IoT 4 Click board based on the nRF9160, with SDK version 2.6.0 and modem firmware version 1.3.6. I read in the documentation that the nRF9160 provides...
We are developing digital stethoscope and would like to use nrf5340-audio DK as starting point. We need to first get the microphone out on the headphones jack in the DK and...
Hi everyone,
I am using SDK Toolchain v2.3.0 and my code is based on the aws_iot example. I am getting either "cJSON Parse failure" or "Failed to print JSON object" error...
Hello, I am using nRF Connect SDK v2.9.0. While working on the nRF52840 board, I used sys_poweroff() to put the board in deep sleep mode. But before calling it, I called ...
