I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi, I am trying to migrate my device from s132 7.2.0 to s332 7.0.1, for adding ANT. I have no more access to the SWD. I know it is not tested : docs.nordicsemi.com/.../lib_bootloader_dfu_validation...
I am attempting to integrate the MM8108 with the NRF54L15 SoC as my lead engineer suggested, but now I am finding that it is not that straightforward. We want to make a HaLow...
Dear All, I am developing an application where I need to get the nRF5340 to the low power state, where the chip is consuming less than 10uA when it idle, while using the nRF7002...
I would like to control the RGB LED on the board. I followed the drievr example provided by the nrf sdk, but it doesn't work. As far as I understand, I don't need the signal...
Does the nRF54L15 internal temperature sensor vary, based on the applied VDD voltage?
I'm wondering if this is what I'm seeing. With a VDD of 3V I'm seeing lower temperature...
Hi, I am trying to build my own board based on the nRF9160 DK. I want to keep both the nRF9160 and the nrf 52840 chips on my board. Can these chips talk to each other directly...
Hi Nordic Team,
We are currently evaluating MCUs for our upcoming product, and our requirements include a device with large RAM and ROM , especially larger code space ....
I've seen this discussed a few times before, but haven't seen a great answer on this. It seems to be commonly known that attaching a debugger while using the IEEE 802.15.4...
Hi,
I have been trying to get Periodic Parent Search active on my nRF54L15DK (and also on an nRF52840DK) without success. My approach has been:
Use the OpenThread CLI...
We are currently using the STM32WL5MOC module and are facing a serious issue with LoRa range. The communication range is not going beyond 1 meter, and the RSSI while receiving...
Greetings,
I have set up some tests using the ZTest environment based on the test sample in ..\v3.0.2\zephyr\tests\bluetooth\adv\. for my custom project which has custom...
Hi,
We are considering using nRF54L15 / SDK3.1.1 -> as a wearable device that is part of a Thread network. We also need to do sporadic BLE connections and channel sounding...
We've a nRF9151 DK for which we built the Nordic Semiconductor LwM2M Client sample using SDK 3.0.2 (modem firmware 2.0.2).
We followed all steps listed in https://docs.nordicsemi...
We are seeing network issues in some particular locations. In these areas, the device is unable to connect to the cloud.
Hardware: nRF9160-based board
Modem firmware...
