But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi Iam work on Linux 5.14.0-1011-oem #11-Ubuntu SMP Mon Dec 13 18:01:14 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux
When I open VScode I got "Shell initialization conflicts...
Hi,
We are evaluating nRF5340 for our new product. We learned that nRF5340 can be used for LE Audio application. However, we want to know whether simultaneous BLE communication...
Hi,
We have developed a BLE module using Zephyr as RTOS on Espressif ESP32C3. Now we're looking to port the same application to the Nordic nRF52810. We have chosen nRF52810...
Hello,
I am working on a custom board using the BC833M ( https://www.digikey.com/en/products/detail/fanstel-corp/BC833M/13174321 ) which uses an nRF52833. I am using a rigid...
Hi,
Customers have reported the problem of dfu upgrade failure, and we also use the same type of mobile phone (iPhone 11 & iPhone XR) for testing. It is found that there...
Hello,
I am relatively new to the nRF Connect SDK and I'm developing an application for nRF9160DK on toolchain version 2.0.2.
I am working on a non-secure application...
Hi, I am trying intialize the RTC in ncs using nrfx drivers and then connect it tick event to a saadc sampling event using a ppi channel. I learnt that RTC0 and RTC1 are used...
Hi
after create project from sample broadcast_audio_sink, when running it, i get following message:
[21:59:46:406] *** Booting Zephyr OS build v3.0.99-ncs1-2483-g482dcc7865f7...
I need to modify the code of different sensor data, which is obtained on LTE monitor, so I want that file in which I can create custom sensor data /Modify the sensor data...
Hello.
I had LC3 access granted.
I can access nrfconnect/sdk-lc3 on my web browser.
However, with bash, I get the following error and cannot build nRF5340_audio.
...
Hi Mate,
I have very small issue that is when i am trying to link config_bootloader_mcuboot=y in zephyr application the program is not flashed. I need to run zephyr application...
I was curious if there was a delta firmware update file to go from 1.3.1 to 1.3.0 on the nRF9160. Most of our business is in North America and we use a carrier who requires...
Hi all,
I'm trying to use the nrf Connect SDK and configure PWM to use in one pin from nordif nrf52DK. The final chip will be the nrf52810. I have configured the builder...
Hello,
I want to use pc-ble-driver WITH an EV-BT8400XE.
I develop with SDK15.3 (last compatible version of SDK for pc-ble-driver)
I am successfully able to use pc-ble...
Hey all together,
I'm using nrf Connect SDK 2.0.0 and want to place a variable in flash at a predefined location. The reason is, that I need to read the information stored...
